An off-grid power system that is tested properly when it is built, and checked on a regular schedule after that, rarely fails without warning. This guide covers safe testing practice, commissioning tests for the array, battery and electronics, the baseline records worth keeping, a maintenance schedule, how to judge panel and battery health over the years, and a step-by-step method for finding faults.
Safety before testing
An off-grid system has several energy sources that cannot all be switched off from one place.
- The array is live whenever light falls on it. Opening a disconnect stops current flowing, but the panel side of the disconnect stays at full open-circuit voltage. A string of three or four current panels can exceed 100 V DC on a cold morning.
- The battery is always live. A short circuit across battery terminals or cables can melt tools, burn skin and start fires. Remove rings and watches, and use insulated tools.
- The inverter output is at lethal AC voltage, and inverters can hold charge in internal capacitors after shutdown. Follow the manual's waiting time before opening a case.
- A generator may start automatically if the system has auto-start. Disable it before working on AC wiring.
Lock out and tag every source before working on a circuit, and confirm with a meter that it is dead. In Canada, CSA Z462 is the standard for workplace electrical safety; in the United States, the equivalent is NFPA 70E. Both describe safe work practice that is worth following at home.
Tools
- Digital multimeter rated for the highest DC voltage in the system, with good-quality probes.
- DC clamp meter. Many low-cost clamp meters read AC only. A DC-capable clamp lets you measure string, charge and inverter current without breaking a circuit.
- Insulation resistance tester for commissioning and for tracking down ground faults. These apply high test voltages and need care.
- Torque wrench or screwdriver with the ranges your equipment manuals specify.
- Infrared thermometer or thermal camera for finding hot connections under load.
- Hydrometer for flooded lead-acid batteries, and eye protection and gloves for handling electrolyte.
Commissioning tests
Commissioning is the set of tests and checks done before the system goes into service. The international standard IEC 62446-1 sets out testing and documentation for PV systems. It is written for grid-connected systems, but its basic tests suit any array:
- Continuity of protective earthing and bonding conductors, where the DC side is earthed or bonded.
- Polarity of every cable, checked before it is connected to a switch, controller or inverter.
- Combiner box checks, confirming each string is connected correctly.
- Open-circuit voltage of each string.
- Current of each string, short-circuit or operating.
- Functional tests of switches, breakers and controls.
- Insulation resistance of the array circuits.
Polarity
Reversed polarity at a charge controller's PV input or battery input can destroy it instantly. Measure every pair of conductors with a multimeter before connecting. The positive probe on the conductor marked positive must give a positive reading.
String open-circuit voltage
Measure each string at the combiner or disconnect with the controller disconnected. Compare the reading with the expected value, corrected for cell temperature, and compare strings with each other. Strings of the same panels measured within a few minutes of each other should read nearly the same.
Worked example: checking string voltages
An array has two strings of three panels. Each panel is rated Voc 37.0 V at 25 °C, with a Voc temperature coefficient of −0.28% per °C. On a cool spring morning the panels are at about 10 °C (50 °F).
Expected Voc per panel: 25 − 10 = 15 °C below rating. 0.0028 × 15 = 0.042. 37.0 × 1.042 = 38.6 V.
Expected Voc per string: 3 × 38.6 = 115.8 V.
String 1 reads 115 V, which is close. String 2 reads 77 V, about two-thirds of the expected value. That points to one panel contributing nothing, often a disconnected or damaged connector inside the string, a reversed panel or a failed panel. A reading of zero means the string is open somewhere. A reading short by roughly one-third of a single panel's voltage points to a failed bypass diode on a panel with three diodes.
String current
Current from a panel rises and falls with sunlight, so a single current reading means little on its own. Measure each string's current with a DC clamp meter, one after another within a minute or two under steady sun, and compare. Strings of the same panels with the same orientation should carry close to the same current. A string carrying noticeably less is shaded, soiled or has a damaged panel or connection.
Insulation resistance
An insulation resistance test applies a DC test voltage between the array conductors and earth to find damaged insulation, pinched cables and water in connectors. IEC 62446-1 sets the test voltage by system voltage and a minimum resistance of 1 MΩ. For arrays below 120 V, follow the tester maker's guidance.
| Array system voltage | Test voltage | Minimum insulation resistance |
|---|---|---|
| 120 V to 500 V | 500 V DC | 1 MΩ |
| 500 V to 1,000 V | 1,000 V DC | 1 MΩ |
| Above 1,000 V | 1,500 V DC | 1 MΩ |
The circuit under test must be isolated with no system voltage present, and the controller and any surge protection disconnected so the test voltage cannot damage them. Many testers refuse to run if they sense voltage on the circuit. Because the array generates voltage in daylight, this test is usually done by an electrician with procedures and equipment designed for PV.
Functional checks
- Open and close every disconnect and breaker and confirm it isolates what its label says.
- Confirm that every charger, controller and the battery monitor show the settings you intended. Record them.
- Start the generator and confirm the inverter-charger accepts it, transfers loads and charges at the expected current.
- Run the largest motor load and confirm the inverter starts it without a low-voltage or overload fault.
- Test low-SOC alarms and generator auto-start, if fitted, by temporarily raising the trigger point.
- Check that the lithium battery's BMS communicates with the inverter-charger, if the system uses this.
Baseline records
Readings taken when a system is new are the reference for every later check. Keep them with the equipment manuals, settings and inspection documents.
| Record | Why it matters |
|---|---|
| Voc of each string, with date, time and panel temperature | Shows later whether a panel or connection has failed |
| Current of each string under steady sun, measured together | Shows uneven strings and degradation |
| Insulation resistance results | A falling reading over the years shows insulation damage |
| All charger, inverter and monitor settings | Lets you restore settings after a reset or replacement |
| Battery capacity test result | Reference for judging battery ageing |
| Daily solar yield on several clear days in each season | Reference for spotting lost output |
| Single-line diagram, with cable sizes, fuse ratings and torque values | Needed for any later repair or inspection |
Maintenance schedule
Adjust the schedule to your equipment manuals, which take priority. A seasonal cabin needs the checks at opening and closing in place of the monthly ones.
Weekly or whenever you are on site
- Check the monitor: minimum overnight SOC, whether the battery reached full, any alarms or error codes.
- Look at the array for snow, frost, leaves or new shade.
Monthly
- Compare solar yield on a clear day with the baseline for the season.
- Check the battery area for heat, odour, swelling, corrosion or electrolyte on surfaces.
- For flooded batteries, check electrolyte levels and take hydrometer readings as our battery guide describes.
- Check that inverter and controller cooling fans run and vents are clear of dust, cobwebs and stored items.
Twice a year, before winter and after spring
- Inspect the array: cracked glass, browning or bubbles in the cells, damaged frames, loose clamps and corroded grounding hardware.
- Check array wiring for chafing, sagging, and chewing by rodents and squirrels.
- Trim trees and brush that have grown into the winter sun path.
- Check enclosure seals and conduit entries for water and insects.
- Run the generator under load and test auto-start.
- Test low-SOC and other alarms.
Yearly
- With all sources isolated, check that connections are tight to the torque values in the manuals. Look for discoloured lugs, melted insulation or corrosion.
- Under load, scan connections with an infrared thermometer or thermal camera.
- Repeat string Voc and current checks and compare with the baseline.
- Check for firmware updates, and record settings after any update.
- Run a battery capacity check, as described below, every year or two.
Snow and cleaning
If you clear snow from panels, use a soft roof rake or brush designed for panels, never a metal shovel or ice chipper, and never stand on panels. If dust, pollen or bird droppings build up, clean the panels only as the panel maker's instructions describe.
Judging panel and battery health
Panel degradation
Solar panels lose output slowly with age. A review by the US National Renewable Energy Laboratory of nearly 2,000 measured degradation rates found a median of 0.5% per year. Panel warranties state their own guaranteed output figures.
Worked example: expected array output after 10 years
A 2,400 W array losing 0.5% per year keeps 0.995 of its output each year. After 10 years: 2,400 × 0.99510 = 2,400 × 0.951 = about 2,283 W, a loss of about 117 W.
If clear-day yield is down 20% from the baseline, ageing does not explain it. Look for shading, soiling, a failed string or a charge controller that is reaching float early because the battery is full.
Lead-acid state of charge
Resting voltage and specific gravity show a lead-acid battery's state of charge, but only after the battery has rested with no charge or load for at least 6 hours, and preferably 24. Trojan Battery publishes these values for its flooded batteries, with specific gravity corrected to 27 °C (80 °F):
| State of charge | Specific gravity | 12 V battery | 24 V bank | 48 V bank |
|---|---|---|---|---|
| 100% | 1.277 | 12.73 V | 25.46 V | 50.93 V |
| 80% | 1.238 | 12.50 V | 25.00 V | 49.99 V |
| 60% | 1.195 | 12.27 V | 24.48 V | 48.96 V |
| 50% | 1.172 | 12.10 V | 24.20 V | 48.41 V |
| 40% | 1.148 | 11.89 V | 23.92 V | 47.83 V |
| 20% | 1.098 | 11.66 V | 23.32 V | 46.63 V |
Trojan recommends equalizing only when specific gravity varies by more than 0.030 between cells after a full charge. Do not add water before taking readings, because it lowers specific gravity. A battery that reads below the table after a full charge may have been over-discharged or have a failed cell. Other makers publish slightly different values; use your battery's data sheet.
LiFePO4 cell balance
Resting voltage tells little about a LiFePO4 battery's state of charge. Check health through the BMS instead: the spread between the highest and lowest cell voltage near full charge, the number of protection events, and cell temperatures. A spread that grows over months, or frequent high-cell-voltage disconnects near full, shows the cells need balancing or one cell is weakening. Follow the battery maker's balancing procedure.
Capacity check
A capacity check shows how much of a battery's rated capacity remains. Charge the battery fully so the monitor synchronizes to 100%. Then run a steady, known load and note how many amp-hours the monitor counts before the battery reaches a set end point, such as the maker's recommended minimum state of charge or voltage.
Worked example: a capacity check on a 48 V bank
A 48 V lead-acid bank is rated 400 Ah at the 20-hour rate. Discharging to 50% should deliver about 200 Ah. The owner runs a steady 1,000 W load from full charge. At about 48 V, that draws 1,000 ÷ 48 = 20.8 A, which is close to the 20-hour rate of 400 ÷ 20 = 20 A.
The bank reaches the 50% resting-voltage point, 48.41 V, after the monitor has counted 160 Ah. Delivered capacity is 160 ÷ 200 = 80% of rated. For accuracy, rest the battery before reading voltage, or use the monitor's count and voltage together.
Record the result and repeat each year or two. A steady fall is normal ageing; a sudden fall points to a failing cell or chronic undercharging.
Fault finding
A method that works
- Read the data first. Error codes, alarm history and the monitor's logs often identify the fault directly. Look up codes in the manual.
- Define the symptom exactly, including when it happens and under what load.
- Check the simple things. Tripped breakers, blown fuses, switches left off, snow on the panels, a battery that is already full.
- Work along the power path. Measure from the source towards the load: array, disconnect, controller input, controller output, battery. The fault lies between the last good reading and the first bad one.
- Change one thing at a time, and record what you changed.
Common symptoms
| Symptom | Likely causes | What to check |
|---|---|---|
| No solar charging on a sunny day | PV breaker or fuse open; controller fault such as PV over-voltage; battery full and in float; low-temperature cut-off; BMS has blocked charging | Controller display and error code; PV input voltage at the controller; battery temperature; BMS status |
| Solar output lower than baseline | Snow, soiling or new shade; one string open or damaged; controller reaching float early | Look at the array; compare string currents; check charge stage |
| Inverter shuts down when a motor starts | Low state of charge; voltage drop in battery cables or a loose connection; motor surge beyond inverter rating | SOC; battery voltage at the inverter terminals during the start; connection temperatures |
| Battery monitor reading drifts or never shows 100% | Monitor never synchronizes; a load or charger wired around the shunt; wrong capacity setting | Charged-voltage and tail-current settings; that all negatives go through the shunt |
| Lead-acid capacity falling quickly | Chronic undercharging and sulphation; one weak cell; low electrolyte | Specific gravity of each cell after full charge; absorption time and voltage settings |
| LiFePO4 battery cuts out without warning | BMS protection: high or low cell voltage, cold, over-current | BMS event log; cell voltage spread; temperature |
| Inverter-charger will not accept generator | Generator voltage or frequency outside the accepted window; input breaker tripped; input disabled in settings | Generator output voltage and frequency at the inverter input; input settings |
Finding a bad connection
A loose or corroded connection has extra resistance. Under heavy current it drops voltage and heats up, which can lead to a fire. You can find it by measuring the voltage across each joint while current flows.
Worked example: voltage drop across a cable lug
With the inverter running a load that draws 120 A from the battery, the owner measures across each bolted connection on the positive cable, with one probe on the lug and the other on the stud or busbar.
Most joints read a few millivolts. One reads 0.060 V. Its resistance is 0.060 ÷ 120 = 0.0005 Ω (0.5 mΩ). The heat produced is current squared times resistance: 120 × 120 × 0.0005 = 7.2 W, concentrated in one small joint.
The owner isolates the battery, takes the joint apart, cleans the contact surfaces, refits it with the correct hardware and torque, and repeats the measurement.
An infrared thermometer or thermal camera finds the same problem faster: compare the temperature of similar connections carrying the same current. A joint much warmer than its neighbours needs attention. Never tighten connections while they carry heavy current.
Ground faults
Many charge controllers, inverters and combiner boxes include ground-fault detection and will shut down or raise an alarm if a conductor contacts a grounded frame. Treat every ground-fault indication as a real fault. Common causes are a cable damaged by a rodent or pinched under a panel frame, and water inside a junction box or connector. Locating a ground fault often requires disconnecting strings one at a time and testing insulation resistance, which is work for an electrician unless you are trained in it.
After a repair or change
- Repeat the relevant commissioning tests and record the results with the date.
- Check that settings survived any replacement or firmware update.
- Additions such as more panels, a larger inverter or a new battery usually need an electrical permit and inspection. Check before buying equipment.
- Tell your insurer about significant changes to the system.
Key points
- The array is live in daylight and the battery is always live. Lock out every source and prove it dead before work.
- At commissioning, check polarity, string voltage and current, insulation resistance and every function, and record the results.
- Compare strings with each other: a string about one panel short in voltage, or low in current, has a fault.
- Panels typically lose about 0.5% of output per year. A larger loss points to shade, soiling or a fault.
- Read lead-acid resting voltage only after at least 6 hours of rest, and check LiFePO4 health through the BMS.
- Run a capacity check every year or two to track battery ageing.
- Find bad connections by voltage drop or temperature under load, and fix them with the battery isolated.
- Get a permit and inspection for additions, and use an electrician for insulation testing and ground faults.
This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.
The Comprehensive Off-Grid Manual
Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.
More guides
Off-Grid Solar Power: How to Size a System
Size an off-grid solar system for Canadian winters: load audit, peak sun hours, array, MPPT, inverter, wiring, fusing, with a full cabin example.
Off-Grid Batteries: LiFePO4 vs Lead-Acid
LiFePO4 vs lead-acid for off-grid power: usable capacity, cycle life, cold-weather charging, bank sizing, wiring, ventilation and lifetime cost.
The Electrical Load Audit and Efficiency
Measure every load with meters and battery monitors, find duty cycles and standby waste, plan peak demand, audit by season, and price efficiency upgrades.