Home › Free guides › Calendar

The Off-Grid Seasonal Operating Calendar

Living  12 min read

An off-grid property runs on the seasons. Solar output, water supply, road access, fire risk and the firewood supply all follow the calendar, and most failures happen when a seasonal job was left too late. This guide sets out the year as a series of tasks, from late winter through freeze-up, for cabins, homesteads and rural homes in Canada and the northern United States. It refers to our other guides for the detail of each system and adds the seasonal rules on burning, wildfire, ticks and bears.

Using the calendar

Seasons arrive at different times across the country. Spring breakup on the BC coast may come weeks before it reaches northern Ontario, and freeze-up on the Prairies comes far earlier than in the Maritimes. Use the months below as a guide, and set your own dates by your local conditions: the first and last frosts, the dates the road firms up and softens, and when the lake freezes and opens.

Keep a property logbook. Each year, write down the dates of key events and when each task was done. After two or three years, the log becomes a more accurate calendar than any general guide.

Year-round and seasonal properties need different calendars. A year-round home must keep every system running through winter, so its fall work is about preparing for heavy use. A seasonal cabin is shut down, so its fall work is about leaving nothing that can freeze, leak, burn or attract animals. Both are covered below, with a separate checklist for opening and closing a seasonal cabin.

Daylight through the year

Day length sets solar output, working hours and when outdoor tasks can be done. The table gives approximate day length at the solstices, calculated from latitude without allowing for terrain, which shortens the effective day in valleys and on north-facing slopes.

LatitudeExampleAround June 21Around December 21
45° NNear Ottawa, Montreal, Halifax15.4 hours8.6 hours
50° NNear Winnipeg, Kamloops, Regina16.1 hours7.9 hours
55° NNear Prince George, Thompson17.1 hours6.9 hours
60° NNear Whitehorse, Yellowknife18.5 hours5.5 hours

Worked example: calculating day length

Day length in hours = 2 × H ÷ 15, where H is the angle in degrees whose cosine equals −tan(latitude) × tan(declination). Declination is the sun's angle north or south of the equator: +23.44° at the June solstice, −23.44° at the December solstice and 0° at the equinoxes.

At 50° N in December: tan 50° = 1.192 and tan(−23.44°) = −0.434. So cos H = −(1.192 × −0.434) = 0.517, which gives H = 58.9°. Day length = 2 × 58.9 ÷ 15 = 7.9 hours.

At the equinoxes in March and September, every latitude has about 12 hours of daylight.

Winter at 55° N gives less than half the daylight of midsummer, and the sun is low, so solar panels collect a small fraction of their summer output. Our guides to solar power and batteries explain how to size for December.

Late winter: January and February

The coldest weeks test every system. They are also the time to plan the year and cut wood while the ground is frozen.

  • Firewood: fell and skid next winter's wood while frozen ground protects the soil. Maryland's woodlot guidance recommends cutting in late winter or early spring so wood has a full drying season. Our chainsaw and woodlot guide covers felling and how much a woodlot can supply.
  • Wood heat: check the chimney monthly in heavy-use months and watch the woodpile. If you are burning faster than planned, buy or cut more now, while there is time to dry it. Our wood heat guide covers creosote and sweeping.
  • Power: keep snow off solar panels, check battery state of charge daily, and run the generator before the batteries fall below the level the maker recommends. Log generator hours for oil changes.
  • Water: check heat-trace, pump-room temperature and any low-temperature alarm. Watch for frozen lines at the first sign of reduced flow.
  • Roads and roofs: clear snow before banks grow too high, keep sand at the top of hills, and watch for roof snow loads above entries and on outbuildings.
  • Ice: keep measuring ice on any lake crossing; snow cover and thaws change it through the winter. Our roads and winter access guide gives thickness guidelines.
  • Planning: order seeds, plan the garden, book spring trades, and order parts and filters for spring maintenance.

Spring breakup: March and April

As the snow melts and frost leaves the ground, roads soften, creeks rise and water can reach places it never does in summer.

  • Roads: keep heavy loads off soft roads until they dry. Clear culverts and ditches of ice and debris so meltwater can pass, and watch crossings during peak runoff.
  • Flooding and wells: if surface water reaches a well head, or water changes colour, taste or smell, stop drinking it and test for bacteria. Our guide to off-grid water covers testing and shock chlorination.
  • Seasonal cabins: open the water system only once the risk of hard frost has passed. Reassemble, flush, check every fitting for leaks, and test the water before drinking.
  • Power: clean panels, check mounting hardware after winter storms, and check battery terminals. Solar output rises quickly from March as the days lengthen.
  • Generator: service it after the winter's heavy use: oil, filter, spark plug and spark arrestor, as the manual directs. Our field repairs guide covers maintenance.
  • Burning brush: spring is a common time to burn winter blowdown, but it is also an early wildfire season, when dead grass is dry before green-up. In Ontario, the forest fire season runs from April 1 to October 31, and in the province's northern regions outdoor burning without a permit is limited to starting no earlier than 2 hours before sunset and putting out no later than 2 hours after sunrise, with piles under 2 m across and 2 m high. Check provincial, state and municipal rules before every burn.
  • Bears: bears leave their dens in spring. Take down bird feeders; BC's government advises using them only in winter, when bears are hibernating. Secure garbage, compost and livestock feed.

Late spring: May and June

  • Garden: plant after your last frost date. Keep row cover handy for late frosts in low-lying gardens, where cold air collects.
  • Firewood: split and stack the wood cut in winter, in sun and wind, so it dries through the summer.
  • Roads: once the surface is damp but firm, grade to restore the crown, fill ruts and remove washboarding, and add gravel where it has thinned.
  • Water: test for bacteria, as our water guide recommends for spring and fall. Change sediment and carbon filters and the yearly UV lamp. On rainwater systems, clean gutters and first-flush diverters after the spring pollen and seed fall.
  • Wildfire preparation: work through the FireSmart home ignition zone before the dry season.
  • Ticks: ticks can be active whenever temperatures are above freezing and the ground is not snow-covered, but are most often met in spring, summer and fall. Blacklegged ticks, which can carry Lyme disease, are established in parts of southern Manitoba, Ontario, Quebec, New Brunswick and Nova Scotia. Check yourself, children and pets after time in brush, long grass and woodpiles, and remove attached ticks as soon as possible.

The FireSmart home ignition zone

ZoneDistance from the houseTasks
Immediate0 to 1.5 m (5 ft)Non-combustible surface: clear to bare soil and cover with gravel, brick or concrete. No woody shrubs or trees.
Intermediate1.5 to 10 m (5 to 33 ft)Fire-resistant landscaping, no mulch or woody debris. No firewood, building materials or stored items. Move sheds and trailers further out, or put a gravel pad 1.5 m around them.
Extended10 to 30 m (33 to 98 ft)At least 3 m between the crowns of evergreen trees. Remove branches up to 2 m above the ground. Clear fallen branches, dry grass and needles regularly.

The firewood stack belongs outside the 10 m line during fire season, which on many properties means moving it twice a year: out in spring and closer to the house before winter.

Summer: July and August

  • Fire season: check fire danger ratings and restrictions daily. Campfire and open burning bans are common. Limit chainsaw and other equipment use in dry, hot weather, keep spark arrestors clean, and keep tools and water on hand. Clear dry grass from around the house and outbuildings.
  • Water: late summer is when springs and shallow wells drop and rainwater cisterns are at their lowest. Measure spring flow now, and track cistern levels against use. Ration before the supply runs out, not after.
  • Power: long days give the year's highest solar output. Run heavy loads in sunny hours: pumping to a cistern, laundry, tool charging, freezing ice.
  • Building work: roofing, painting, foundation and road work go best in dry weather. Book trades early; rural contractors fill their summers quickly.
  • Food: harvest, preserve and store. Our food storage guide covers methods and root cellars.
  • Wildfire plan: know your evacuation routes, have a bag packed, and decide in advance what triggers leaving. With one road in and out, leave early.

Fall: September and October

Fall is the busiest season on an off-grid property. Every winter problem has to be solved before freeze-up.

  • Firewood: move the dry wood under cover and close to the house. Check that you have the full winter's supply plus a margin; our wood heat guide shows how to calculate it.
  • Wood heat: sweep and inspect the chimney before the first fire of the season. Check gaskets, the stovepipe and the chimney cap. Test smoke and carbon monoxide alarms and replace any past their stated life.
  • Water: test for bacteria again. Insulate and heat-trace exposed lines, check the pump-room heat, and service the pressure system. On seasonal cabins, drain and winterize everything before the first hard frost, as our water guide sets out.
  • Roads: clean culverts and ditches before freeze-up, stake road edges and culverts, set up the plow, and stock sand. Arrange the contractor if one clears your road.
  • Fuel: fill propane, heating oil and generator fuel tanks while delivery trucks can still reach you. Stock oil, filters and spark plugs for winter generator service.
  • Vehicles: fit winter tires by the legal date where it applies: October 1 on most signed highways in BC, December 1 in Quebec. Check block heaters, batteries and the winter vehicle kit.
  • Power: check that the battery bank is healthy before the dark months, and service the generator before it starts carrying the winter load.
  • Bears: bears feed heavily in fall before denning. Pick fruit as it ripens, keep compost free of meat and cooked food, and lock poultry and livestock in at night if a bear is around.
  • Garden: harvest and store root crops, plant garlic, and mulch perennials.

Worked example: stocking for freeze-up

Example figures. A property expects that freeze-up, when lake ice is too thin to cross and the road is unreliable, may cut it off for up to 21 days. The generator burns about 1.5 L of gasoline an hour and runs 3 hours a day in November.

Fuel for the closure: 1.5 L × 3 h × 21 days = 94.5 L. Add 25% for a longer closure or heavier use: 94.5 × 1.25 = about 118 L, or six 20 L cans.

Gasoline goes stale in storage. Add stabilizer as the fuel maker directs, store cans in a ventilated shed away from the house, and use the oldest fuel first. Do the same calculation for propane, food, medicines and animal feed.

Early winter: November and December

  • Freeze-up: stay off new ice until it has been measured in several places.
  • Power: the shortest days of the year bring the lowest solar output. Shift loads, watch battery charge closely, and run the generator on schedule rather than waiting until the batteries are low.
  • Snow: plow early and push banks well back. Keep solar panels and roof vents clear.
  • Bird feeders: once bears are denned for the winter, feeders can go back up.
  • Maintenance: walk the systems weekly: water, heat, power, roof and road. Small problems in December become emergencies in January.
  • Records: review the year's logbook, note what failed and what ran short, and set next year's dates.

Opening and closing a seasonal cabin

A cabin used only in the warmer months has two critical days each year: opening and closing. Work from a written checklist kept at the cabin, and tick it off each time.

Opening in spring

  1. Walk around the outside before going in. Look for fallen trees, roof damage, broken windows, animal entry and signs of water.
  2. Open up and ventilate. Check for mice and other animal droppings; wet them with disinfectant before cleaning, rather than sweeping them dry, and wear gloves and a mask.
  3. Check the chimney cap and flue for nests before lighting the stove.
  4. Reconnect the battery bank and solar array in the order the system manuals give, then check the inverter and charge controller readings.
  5. Reassemble the water system, fit new filter cartridges, refill slowly and check every fitting for leaks before leaving it pressurized. Flush and test the water before drinking it.
  6. Test smoke and carbon monoxide alarms, and replace batteries where needed.
  7. Start the generator and run it under load. Check the propane system for leaks with the method the supplier recommends.
  8. Clear the road and check culverts and the parking area before bringing in heavy loads.

Closing in fall

  1. Drain and winterize the water system completely, as our water guide describes, including the pump, pressure tank, water heater and every trap.
  2. Remove all food, drinks that can freeze, and anything that attracts animals. Leave cupboard doors and the fridge propped open.
  3. Charge the batteries fully and leave them in the state the maker recommends for storage. A fully charged lead-acid battery is much less likely to freeze than a discharged one.
  4. Run engines' carburettors dry or add stabilizer to their fuel. Store fuel outside the cabin.
  5. Close the propane supply at the tank.
  6. Let the stove burn out completely, then remove and safely dispose of the ashes.
  7. Close the chimney damper if fitted, cap open vents against animals, and secure doors and shutters.
  8. Photograph the inside and outside for insurance, and arrange for someone to check the property during the winter if your policy requires it.

Tasks every month

  • Test smoke and carbon monoxide alarms.
  • Walk the property's systems: look for leaks, listen to the pump, read the battery and inverter displays, check for warm or discoloured electrical connections.
  • Start and run the backup generator under load if it has not been used.
  • Check first-aid kits, fire extinguishers and emergency supplies.
  • Record fuel use, generator hours, water levels and firewood burned.

Year at a glance

MonthsMain tasks
January to FebruaryCut firewood on frozen ground; watch batteries, chimney and pipes; plan and order
March to AprilProtect roads during breakup; clear culverts; reopen seasonal water; service generator; bears return
May to JunePlant; split and stack wood; grade road; spring water test and filters; FireSmart work; tick checks
July to AugustFire restrictions; monitor water supply; use peak solar; building and road projects; preserve food
September to OctoberSweep chimney; fall water test; winterize; fill fuel; winter tires; stake roads; bear-proof
November to DecemberFreeze-up caution; manage low solar; plow early; weekly system checks; review the year

Key points

  • Set the calendar by your own local dates for frost, breakup and freeze-up, and keep a logbook.
  • December daylight falls to about 7.9 hours at 50° N and 6.9 hours at 55° N; plan power for it.
  • Cut firewood in late winter, split and stack it in spring, and bring it in by fall.
  • Keep heavy loads off roads during breakup, and clear culverts before both thaw and freeze-up.
  • Test water in spring and fall, and after any flooding.
  • Work the FireSmart zones before summer: non-combustible to 1.5 m, no stored fuel within 10 m.
  • Follow seasonal burning rules; Ontario's fire season runs April 1 to October 31.
  • Take bird feeders down while bears are active, and check for ticks from spring to fall.
  • Fill fuel and supplies before freeze-up, sized to the longest closure you expect.

This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.

The Comprehensive Off-Grid Manual

Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.

Living

Planning an Off-Grid Property in Stages

Build an off-grid homestead in stages: a year of site observation, a master site plan, temporary living, first buildings, water, septic and systems that grow.

13 min read