Home › Free guides › Wind

Small Wind Turbines for Off-Grid Power

Power  12 min read

A small wind turbine can add useful energy to an off-grid system, especially on open, exposed sites. It can also be one of the most disappointing purchases a rural owner makes. Output depends on the cube of wind speed, so a site that is only slightly less windy than hoped produces far less than expected, and a turbine mounted too low among trees or buildings produces very little at all. This guide explains the physics that decides output, how to judge a site, the siting rule for tower height, how to estimate annual energy with real numbers, turbine certification, towers, battery-system integration, permits, costs and maintenance, for properties in Canada and the northern United States.

How much power is in the wind

The power a turbine captures is:

Power (W) = ½ × air density (kg/m³) × swept area (m²) × wind speed (m/s)³ × Cp

  • Air density is about 1.225 kg/m³ at sea level and 15 °C. Cold air is denser: at −20 °C it is about 1.225 × 288 ÷ 253 = 1.39 kg/m³, roughly 14% more. High elevations have thinner air and less power.
  • Swept area is the circle the blades sweep: π × (rotor diameter ÷ 2)². Doubling the rotor diameter quadruples the swept area and the power.
  • Wind speed cubed is the dominant term. Doubling wind speed gives eight times the power.
  • Cp, the power coefficient, is the fraction of the wind's power the turbine actually converts. The theoretical maximum, known as the Betz limit, is 0.59. The US National Renewable Energy Laboratory (NREL) gives practical values of 0.25 to 0.45 for small turbines.

Worked example: the effect of wind speed

A turbine has a 3.6 m (11.8 ft) rotor. Swept area = π × 1.8² = 10.2 m². Take Cp as 0.35 and air density as 1.225 kg/m³.

At 5 m/s (11 mph): ½ × 1.225 × 10.2 × 5³ × 0.35 = ½ × 1.225 × 10.2 × 125 × 0.35 = 273 W.

At 6 m/s (13 mph): 6³ = 216, so power = 273 × 216 ÷ 125 = 472 W.

A 20% increase in wind speed raises power by 1.2³ = 1.73, or 73%. The reverse is also true: a site with 20% less wind than you assumed gives only 0.8³ = 0.51, about half, of the expected power.

Elevation

Air density falls with elevation. In the standard atmosphere it is about 1.06 kg/m³ at 1,500 m (4,900 ft), about 14% less than at sea level, so a turbine on a high plateau produces about 14% less at the same wind speed. Certified ratings assume sea-level density, so reduce them for high sites. In winter at the same site, colder air partly offsets the loss.

This is why the average wind speed at hub height, and how accurately you know it, matters more than any other figure in a wind project.

Judging the wind resource

The US Department of Energy (DOE) advises that a site should have an average annual wind speed of at least 9 mph (4 m/s) for a small wind system to be practical. NREL puts the threshold for off-grid hybrid systems at the same 9 mph (4.0 m/s), and for grid-connected systems at about 10 mph (4.5 m/s).

Sources of wind data

  • Wind maps and atlases: regional wind maps give modelled average speeds at set heights. They are useful for screening but cannot account for the trees, hills and buildings on your own lot.
  • Airport and weather station data: measured, but usually at only 6 to 10 m (20 to 33 ft) above ground and at a different site. NREL notes that wind at an 80 ft (24 m) hub height may be 15% to 25% faster than at airport anemometer height.
  • Your own measurements: an anemometer and data logger on a mast at or near proposed hub height, recording for at least a year, gives the only reliable picture of your site. NREL gave a cost of US$600 to $1,200 for wind measurement equipment.
  • Physical signs: trees permanently bent or flagged by the prevailing wind indicate a strong, steady resource.

Siting and tower height

The standard siting rule, given by both DOE and NREL, is that the bottom of the rotor should be at least 9 m (30 ft) above anything within 90 m (300 ft) of the tower. In a forest of 18 m (60 ft) trees, that puts the lowest blade tip at 27 m (90 ft) or more, and the hub higher still.

Worked example: minimum tower height

The tallest tree within 90 m (300 ft) of the proposed site is 15 m (49 ft). The turbine's rotor is 3.6 m in diameter.

Lowest blade tip: 15 + 9 = 24 m.

Hub height: 24 + 3.6 ÷ 2 = 25.8 m (85 ft).

Trees grow. If those trees will gain another 5 m (16 ft) over the turbine's 20-year life, plan for a hub at about 31 m (102 ft), or arrange to manage the trees.

Taller towers cost more but often pay for themselves. NREL's example is that raising a 10 kW system from a 60 ft (18 m) to a 100 ft (30 m) tower adds about 10% to the system cost and can produce about 25% more power.

Estimating annual energy

NREL gives a simple estimate of annual energy output (AEO) for a small turbine:

AEO (kWh per year) = 0.01328 × D² × V³

where D is the rotor diameter in feet and V is the annual average wind speed at hub height in miles per hour. The formula allows for the way real wind varies around its average.

Worked example: annual energy from a 3.6 m rotor

Convert units: 3.6 m × 3.281 = 11.8 ft. An average of 5 m/s × 2.237 = 11.2 mph.

At 5 m/s: 0.01328 × 11.8² × 11.2³ = 0.01328 × 139.2 × 1,405 = about 2,600 kWh per year, or 2,600 ÷ 365 = 7.1 kWh per day on average.

At 6 m/s (13.4 mph): 0.01328 × 139.2 × 13.4³ = about 4,450 kWh per year, or 12.2 kWh per day.

As a cross-check, the 273 W calculated earlier at a steady 5 m/s gives 273 × 8,760 hours = 2,391 kWh per year, close to the formula's result.

Compare these daily averages with your load audit. A cabin using 2.5 kWh a day could be covered on average by this turbine at 5 m/s, but the average hides calm weeks with almost no output, so batteries and a second source are still needed.

Manufacturer ratings

A turbine's advertised "rated power" is the output at a particular wind speed chosen by the manufacturer, and can be misleading. Compare turbines by swept area, certified power curve and certified annual energy instead.

Choosing a turbine size

The DOE says residential turbines typically range from 400 W to 20 kW, and that a home using about 10,649 kWh a year, the US average it cites, would need a turbine of 5 to 15 kW to meet a significant share of that demand, depending on wind speed. Its example of a small system is a 1.5 kW turbine meeting a 300 kWh per month load at an average of 14 mph (6.26 m/s).

Off-grid loads are usually far smaller than those of a grid-connected home. Work backward from your audit:

  1. Take the daily load from your load audit, in kWh, and multiply by 365 for the annual load.
  2. Decide what share wind should supply. On a hybrid system it might be a third to a half, with solar and a generator covering the rest.
  3. Rearrange the AEO formula to find the rotor diameter: D (ft) = √(AEO ÷ (0.01328 × V³)).

Worked example: rotor size for a hybrid cabin

A year-round cabin uses 3 kWh a day, or 3 × 365 = 1,095 kWh a year. The owner wants wind to supply half: about 550 kWh a year. Measured average wind at the planned hub height is 4.5 m/s, which is 4.5 × 2.237 = 10.1 mph.

V³ = 10.1³ = 1,030. D = √(550 ÷ (0.01328 × 1,030)) = √(550 ÷ 13.7) = √40.1 = 6.3 ft, or 6.3 ÷ 3.281 = 1.9 m.

A turbine with a rotor of about 2 m (6.6 ft) would be the starting point. If the true average were only 4 m/s (8.9 mph), the same rotor would give 0.01328 × 6.3² × 8.9³ = 0.01328 × 39.7 × 705 = about 370 kWh a year, a third less. Size with margin, or measure before buying.

Calm periods

Average output hides calm spells of several days. Size the battery for the load over the longest calm period you are prepared to bridge without the generator, using the method in our battery guide, and treat wind as energy that shortens generator runs rather than as a guaranteed daily supply.

Turbine certification

Small turbines in the United States are certified for performance, safety and sound to ANSI/ACP 101-1-2021, the Small Wind Turbine Standard, or to the earlier AWEA 9.1-2009. Certification listings also reference IEC 61400-1, 61400-11 and 61400-12, the international standards for design, acoustic noise and power performance. Certified turbines carry a consumer label with standard figures:

Label figureWhat it means
Reference annual energyAnnual energy at a stated average wind speed with a standard wind distribution, sea-level air density and 100% availability
Reference power at 11 m/sOutput at 11 m/s (24.6 mph) in standard conditions, the common basis for comparing turbines
Reference sound levelThe sound level in dB(A) not exceeded 95% of the time, measured 60 m (197 ft) from the rotor hub
StandardThe standard the turbine was certified to, such as ACP 101-1-2021

Certification is done by bodies such as the Small Wind Certification Council (SWCC), which publishes lists of certified turbines. An uncertified turbine has no independent check on its power curve, durability or noise. In Canada, the turbine's electrical equipment, including any controller and inverter, must also be certified for use in Canada, as described in our solar power guide.

Tower types

TowerDescriptionConsiderations
Guyed lattice or tubeA slender tower held upright by guy wires anchored in the groundLowest cost per metre of height; needs a large clear area for guys
Tilt-up guyed towerA guyed tower hinged at the base so it can be lowered with a winch or gin poleAll turbine maintenance is done at ground level; needs clear space to lower it
Freestanding lattice or monopoleSelf-supporting tower on a large concrete foundationSmallest footprint; highest cost; maintenance requires climbing

NREL gives the guy wire radius as one-half to three-quarters of the tower height. A 30 m (98 ft) guyed tower therefore needs guy anchors 15 to 22.5 m (49 to 74 ft) from its base in each direction, and a clear circle twice that across. A tilt-up tower also needs a clear strip at least as long as the tower in the direction it is lowered.

Connecting a turbine to an off-grid system

Most small off-grid turbines charge a battery bank through their own controller, alongside the solar charge controller. Points to plan:

  • Battery bank: NREL notes that off-grid battery banks are typically sized to supply the load for one to three days. Wind does not remove the need for storage; it changes when the batteries are recharged.
  • Diversion load: many battery-charging turbines must stay electrically loaded so they do not overspeed. Their controllers divert surplus energy to a resistive dump load, such as a water or air heating element, once the battery is full. Size the dump load to the turbine's maximum output as the manufacturer specifies.
  • Braking and shutdown: install the manufacturer's stop switch or brake, and know how to stop the turbine before a storm or for maintenance.
  • Wire run: the tower is often far from the battery. Calculate voltage drop for the full distance as shown in our solar sizing guide; a higher-voltage turbine or controller reduces cable size and loss.
  • Lightning and grounding: an exposed tower is a lightning target. Bond and ground the tower and fit surge protection where the turbine cable enters the building, following the manufacturer and the electrical code.
  • Hybrid with solar: wind and solar together can reduce the battery size and generator hours needed, because a calm sunny day and a windy cloudy day each still produce something.

Permits, zoning and neighbours

Check rules before buying a turbine.

  • Zoning and height limits: many municipalities limit structure heights. NREL noted that zoning height limits in the US are often about 35 ft (11 m), well below an effective tower. Ask whether a variance or a specific wind bylaw applies.
  • Building permit: ask the building department whether the tower and foundation need a permit and engineered drawings.
  • Electrical permit: wiring the turbine, controller and dump load is electrical work under the Canadian Electrical Code, as adopted by each province, or the NEC in the US. Section 64 of the Canadian Electrical Code covers renewable energy systems.
  • Setbacks: ask what distance the tower must keep from property lines, roads and power lines. At the least, keep it far enough away that a falling tower cannot reach a building, road or power line.
  • Noise: NREL reported that modern residential turbines produce about 52 to 55 dB of sound. Check the certified sound level and talk to neighbours before installing.
  • Covenants and insurance: check property covenants and tell your insurer about the tower.

The DOE consumer guide also suggests that a small wind system needs at least 0.2 ha (½ acre) of land, mainly to provide clearance around the tower.

Cold climates

  • Operating temperature: check the turbine's and controller's rated temperature range against your record low. Lubricants, seals and electronics all have limits.
  • Icing: freezing rain and rime ice add weight to blades, unbalance the rotor and cut output. Many owners stop the turbine during heavy icing. Ice can be thrown from moving blades, so keep people and vehicles out of the area below the rotor in icing weather.
  • Battery charging: wind often blows hardest on cold nights. If the bank is LiFePO4, its battery management system may block charging below freezing, as our battery guide explains, so the diversion load must be able to absorb the turbine's full output when charging stops.
  • Access: plan how you will reach the tower base and lower a tilt-up tower in deep snow.

Costs and lifespan

Published cost figures are dated and vary widely by turbine size, tower and site. DOE's 2010 consumer guide gave installed costs of US$4,000 to $8,000 per kW. Get current quotes for the complete installed system, including tower, foundation, wiring, controller, dump load and permits.

Worked example: cost per kilowatt-hour

Suppose a complete installation with the 3.6 m rotor above costs $30,000 and produces 2,600 kWh a year at a 5 m/s site. Over a 20-year life, it produces 2,600 × 20 = 52,000 kWh. The capital cost alone is 30,000 ÷ 52,000 = $0.58 per kWh, before maintenance and any replacement parts.

At a 6 m/s site the same system produces 4,450 × 20 = 89,000 kWh, and the cost falls to 30,000 ÷ 89,000 = $0.34 per kWh. Compare the result with the cost of more solar, more battery or generator fuel for your site.

Maintenance

NREL's annual checks for a small turbine are:

  • check and tighten bolts and electrical connections;
  • inspect for corrosion;
  • check guy wire tension;
  • check blades and replace worn leading-edge tape if needed.

Blades or bearings may need replacing after about 10 years, and a properly installed and maintained turbine should last up to 20 years or longer. Inspect after every severe storm.

Key points

  • Power rises with the cube of wind speed: 20% more wind gives 73% more power, and 20% less gives about half.
  • Look for an average of at least 4 m/s (9 mph) at hub height, and measure your own site for a year if you can.
  • Keep the bottom of the rotor at least 9 m (30 ft) above anything within 90 m (300 ft); never mount a turbine on a building.
  • Estimate annual energy with AEO = 0.01328 × D² × V³ (feet and mph); a 3.6 m rotor gives about 2,600 kWh a year at 5 m/s.
  • Buy a turbine certified to ACP 101-1, and compare certified power at 11 m/s, reference annual energy and sound level.
  • Plan for a diversion load, braking, voltage drop, lightning protection and one to three days of battery storage.
  • Check zoning, building and electrical permits before buying, and do the cost-per-kWh arithmetic for your own wind speed.

This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.

The Comprehensive Off-Grid Manual

Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.

Power

Off-Grid Batteries: LiFePO4 vs Lead-Acid

LiFePO4 vs lead-acid for off-grid power: usable capacity, cycle life, cold-weather charging, bank sizing, wiring, ventilation and lifetime cost.

13 min read
Power

The Electrical Load Audit and Efficiency

Measure every load with meters and battery monitors, find duty cycles and standby waste, plan peak demand, audit by season, and price efficiency upgrades.

13 min read