Home › Free guides › Chainsaws

Chainsaws, Firewood Cutting and Woodlot Management

Tools  13 min read

A chainsaw is the most useful tool on a wooded property and the one most likely to put the owner in hospital. This guide covers choosing a saw, the protective gear and the standards it should meet, fuel and chain care, kickback, a safe felling sequence, limbing and bucking, how much firewood a woodlot can grow each year, tax programs for managed forests, and the rules for cutting firewood on public land in Canada and the northern United States.

Choosing a saw

Gas or battery

Gas saws give the most power and run all day on a can of mixed fuel. Battery saws start at the push of a button, are quieter, need no fuel mixing and vibrate less, but each battery must be charged from the house system or a generator. Many owners keep a battery saw for limbing and clean-up and a gas saw for felling and bucking.

Size

Saw size is described by engine displacement in cubic centimetres (cc) and by bar length. A saw too small for hardwood or large trees strains and wears out early. A saw too large is heavy, and tired operators make mistakes. Beginners should start with a lighter saw and a shorter bar, which is also easier to control when limbing.

Safety features to insist on

  • Chain brake: stops the chain when the front hand guard is pushed forward or, on most saws, when the saw is thrown back by kickback.
  • Chain catcher: a pin under the bar that catches a broken or derailed chain.
  • Throttle interlock: the throttle cannot move unless the rear handle is gripped.
  • Anti-vibration mounts: reduce hand and arm fatigue.

In Canada, the product standard for chainsaws is CSA Z62.1, and federally regulated employers must use saws that meet it. Check for the certification mark before buying a used or imported saw.

Protective gear

Chainsaw injuries are common and serious. A Penn State Extension review of US data found that about 127,944 people were treated in US emergency departments for chainsaw-related injuries from 2018 to 2022, roughly 70 a day. Most were open wounds, and arms and legs together accounted for more than 80% of patients. Head and neck injuries were more than 10% of cases and often fatal.

Workplace rules do not bind a private owner cutting on their own land, but they are a sound minimum for anyone.

ItemWhat it doesStandards to look for
Chaps or chainsaw pantsLayers of long fibres that pull out and jam the sprocket when the chain touches themWorkSafeBC accepts ASTM F1414, ISO 11393-2 or EN 381-5 test methods; in the US, labels referencing ASTM F1897
Hard hatProtects against falling limbs and kickback strikesCSA Z94.1 or ANSI/ISEA Z89.1
Eye and face protectionStops chips and twigs; a mesh visor plus safety glasses is commonCSA Z94.3 or ANSI/ISEA Z87.1
Hearing protectionEarmuffs or plugs, often built into a forestry helmetChoose by rated noise reduction
BootsProtective toe, grip on wet wood; chainsaw-rated boots add cut resistanceCSA Z195; chainsaw protection is shown by a white label with a green fir tree
GlovesGrip and protection from cuts and splintersHeavy-duty work gloves; cut-resistant models available

Under the BC Occupational Health and Safety Regulation, section 8.21, any worker operating a chainsaw must wear leg protection meeting one of the listed standards. In the US, OSHA's logging standard, 29 CFR 1910.266, requires cut-resistant leg protection for every chainsaw operator, covering the leg from high on the thigh to the top of the boot.

Fuel and maintenance

Mixing fuel

Most two-stroke saws run on a mix of gasoline and two-stroke oil. Stihl specifies 50 parts gasoline to 1 part oil, which is about 20 mL of oil per litre. Follow the ratio in your own saw's manual; too little oil scores the piston and cylinder.

Worked example: mixing a can of fuel

At 50:1, oil needed = gasoline volume ÷ 50.

  • 5 L of gasoline ÷ 50 = 0.1 L, or 100 mL of oil.
  • 4 L of gasoline ÷ 50 = 80 mL of oil.
  • For a 1 US gal can (3.785 L): 3.785 ÷ 50 = 0.076 L, or about 76 mL (2.6 fl oz) of oil.

Mix only what you will use within a month. Stihl advises that home-mixed fuel may no longer be fit for use after 30 days of storage. Gasoline with up to 10% ethanol (E10) is generally suitable for current Stihl saws; check your manual for other brands.

Daily checks

  • Chain brake engages and stops the chain.
  • Chain tension: the chain should move freely by hand along the bar but not sag away from the underside. Check a new chain after its first few minutes of running, since it stretches.
  • Bar oil reaches the chain: hold the running bar tip over a light surface and look for a line of oil spray.
  • Air filter and spark arrestor screen clean, all nuts tight.

Chain sharpening

Sharpen when the saw has to be pushed into the wood or when it makes fine dust instead of chips. A sharp chain pulls itself into the cut. Use a round file of the diameter the chain maker specifies; Oregon, for example, uses a 4.0 mm (5/32 in) file for its 3/8 in low-profile chain and a 4.8 mm (3/16 in) file for .325 in pitch chain. A file guide holds the file at the correct height and angle.

  • Line up the file with the witness mark stamped on each cutter. When a cutter is worn back to that mark, replace the chain.
  • Check the depth gauges (rakers) every few sharpenings with a depth gauge tool and file them down to the setting for your chain.
  • Touching a rock or the ground dulls a chain instantly. Lift logs off the ground before bucking where you can.

Bar care

Turn the bar over at each sharpening so it wears evenly. File off rail burrs and keep the oil hole clear. Replace a bent bar, or one where a correctly tensioned chain wobbles side to side.

Kickback and safe handling

Kickback happens when the upper part of the bar tip touches wood or the chain is pinched at the top of the bar. The saw is thrown up and back toward the operator faster than anyone can react. It is a leading cause of chainsaw injuries.

  • Know where the bar tip is at all times, and keep it away from logs, branches and the ground.
  • Use the low-kickback chain supplied with homeowner saws. Its bumper drive links limit how much the cutter can bite in the kickback zone. It cuts more slowly, and bore cuts with it are slow or impossible.
  • Hold the saw with both hands, thumbs wrapped around the handles, and stand to the side of the cutting line.
  • Run the saw at full throttle when cutting. A slowly moving chain grabs.
  • Never cut above shoulder height.
  • Engage the chain brake before walking with the saw running.
  • Start the saw on the ground, or held firmly between the legs, with the chain brake on. Never drop-start it.

Felling a tree

Many extension services teach a five-step felling plan. Do each step every time, for every tree.

  1. Look at the tree and its surroundings. Check lean, dead branches overhead, rot at the base, and anything the tree could hit.
  2. Choose the felling direction. Pick an open gap close to the natural lean.
  3. Clear the work area and escape routes. Clear brush around the base. Plan two escape routes at about 45 degrees back from the felling direction, away from the line of fall. Clear them before cutting.
  4. Cut the notch. See below.
  5. Make the back cut, leaving a hinge, and retreat. When the tree starts to fall, engage the chain brake, step away along an escape route, and watch the crown.

The notch and hinge

The notch, sometimes called the face cut, sets the direction of fall. University of Wisconsin forestry extension describes an open-face notch with a top cut at about 70 degrees, cut in about one-quarter of the tree's diameter, and a horizontal bottom cut that meets it.

The back cut goes in from the opposite side, level with or just above the bottom of the notch. Stop before it reaches the notch, leaving a strip of uncut wood called the hinge. The hinge steers the tree as it falls. Wisconsin extension gives a minimum of about 25 mm (1 in) of hinge, and 38 to 50 mm (1½ to 2 in) for larger trees. Never cut through the hinge.

Use plastic felling wedges in the back cut to keep the bar from being pinched and to help tip a tree that stands upright or leans slightly back. Do not use steel wedges; they destroy chains.

Worked example: laying out a cut

A trembling aspen measures 360 mm (14 in) across at stump height and leans slightly toward an open clearing.

Notch depth: one-quarter of 360 mm = 90 mm (3.5 in). Cut the 70-degree top cut first, then the horizontal bottom cut to meet it exactly.

Hinge: for a tree of this size, aim for about 25 to 38 mm (1 to 1½ in).

Back cut: start on the far side, level with the bottom of the notch, and cut toward the notch until 25 to 38 mm remains. Tap in a wedge once the bar is fully in the cut.

When to stop and call a professional

  • The tree is within reach of a power line. BC Hydro advises keeping yourself, tools, ladders and any branches you are cutting 3 to 6 m (10 to 20 ft) away from power lines, depending on voltage. For trees near utility lines, call the utility first.
  • The tree leans heavily toward a building, or has a split trunk or large dead limbs.
  • A tree has hung up in another tree. Never cut the tree it is resting on and never walk under it.
  • The diameter is larger than you have been trained to handle.

Limbing and bucking

Limbing

Stand on the uphill side, keep the trunk between you and the saw where possible, and work from the base toward the top. Leave branches holding the trunk off the ground until last, and expect the trunk to roll when they are cut.

Tension and compression

A log supported at both ends sags in the middle. The top of the sag is in compression and the bottom is in tension. A log supported at one end, with the free end hanging, is the reverse. Cutting into the compression side closes the cut and pinches the bar. Cutting the tension side first can make the log split or spring.

The usual method is to cut about one-quarter of the way through on the compression side first, then finish from the tension side. Check how the log moves after each cut, and keep a wedge handy in case the bar is pinched.

Spring poles

A sapling or branch bent under a fallen trunk can whip into the operator when cut. Release it with shallow cuts on the inside of the bend, standing clear of its path, or leave it for someone trained.

Bucking firewood

  • Cut pieces a little shorter than the firebox depth so they load easily. Mark a stick at that length to measure each cut.
  • Kneel for cuts below thigh height and bend at the knees, not the back.

How to split, stack, dry and measure firewood, and how much energy each species holds, are covered in our guide to wood heat.

How much wood a woodlot grows

A woodlot can supply firewood indefinitely if the cut each year does not exceed what the stand grows. Growth rates vary widely with species, soil, climate and stand age.

  • Cornell Cooperative Extension estimates about 0.5 cord per acre per year from stands roughly 20 to 60 years old on moderate to good sites, while still growing a timber crop.
  • Maryland's Department of Natural Resources gives about 2 cords per acre per year for good hardwood land, and notes that poorer sites may need several acres to supply the same amount.

Use the lower figure for planning unless a forester has measured your stand.

Worked example: how many acres to heat a house

A house burns 4.3 cords a winter. At 0.5 cord per acre per year:

4.3 ÷ 0.5 = 8.6 acres, or 8.6 × 0.405 = about 3.5 ha (8.6 acres) of productive woodlot.

At 2 cords per acre per year, the same house needs 4.3 ÷ 2 = 2.15 acres, or about 0.9 ha.

Maryland's tree-volume table gives about 0.33 standard cord for a single tree 300 mm (12 in) in diameter at breast height and 18 m (60 ft) tall. Taking trees of that size, 4.3 cords means about 4.3 ÷ 0.33 = 13 trees a year.

Which trees to cut

  • Keep crop trees: straight, healthy stems of desirable species with full crowns at least as tall as their neighbours. Mark them with flagging tape before cutting so they are not damaged.
  • Cut first: crooked, forked, diseased, damaged or dying trees; suppressed trees crowded under the canopy; and large, spreading, low-value trees that shade out better ones.
  • Leave wildlife trees: dead snags with cavities provide nesting sites. Leave those that pose no risk to trails or buildings. Felling them is also dangerous.

Maryland's guidance suggests cutting in late winter or early spring so the wood has a full drying season before use. Frozen ground in winter also limits soil damage from skidding.

Managed forest tax programs

Several jurisdictions lower property tax on private forest land that is managed under an approved plan.

ProgramMinimum areaMain conditions
Ontario Managed Forest Tax Incentive Program (MFTIP)4 ha (9.88 acres) of forest on one propertyForest land taxed at 25% of the municipal residential rate. Ten-year plan prepared or approved by a Managed Forest Plan Approver; progress report due in year five. Residences and landscaped areas do not qualify.
British Columbia managed forest class25 ha, run as one operationOwner files a forest management commitment with the Managed Forest Council and agrees to follow the Private Managed Forest Land Act. At least 70% of parcels up to 50 ha must be productive forest.

Other provinces and states have their own programs with different conditions. Ask your forestry ministry or assessment office what applies, and note that a registered professional forester can prepare the management plan most programs require.

Cutting firewood on public land

Rules differ by jurisdiction, and the programs below all forbid selling the wood.

British Columbia

Personal-use firewood on vacant Crown land needs a Free Use Permit for Firewood from each Natural Resource District where you cut. The permit is free. Only dead or downed trees may be cut, the wood may not be sold, and you must carry the permit and maps while cutting. Some districts close areas or issue no permits, and permits are not issued until the fire danger rating is moderate.

Ontario

In the Northern Boreal and Managed Forest zones, a household may collect up to 10 m³ of downed wood a year from Crown land without an authorization. Ontario notes that 5 m³ of solid wood is roughly 2 full cords. Anything more, up to 20 m³ a year of standing or downed wood, needs a paid authorization through the Natural Resources Information Portal. Heavy equipment such as tractors and skidders may not be used, and authorizations are not issued in the Southern Ontario/Great Lakes zone.

United States national forests

National forests sell personal-use firewood permits, with prices, limits and rules set by each forest. As an example, the Chequamegon-Nicolet National Forest in Wisconsin charges $5 per cord, with a $20 minimum (4 cords) and a maximum of 12 cords per person per year. Only dead trees may be cut, standing dead trees over 18 in (460 mm) in diameter may not be felled, and no cutting is allowed within 100 ft (30 m) of lakes, streams and beaver ponds.

Key points

  • Buy a saw sized to your trees and your experience, with a chain brake, chain catcher and low-kickback chain.
  • Wear chaps or chainsaw pants, a hard hat, eye and hearing protection, gloves and protective boots, and never cut alone.
  • Mix fuel at the ratio in your manual (50:1 is 20 mL of oil per litre) and use home-mixed fuel within 30 days.
  • Sharpen often, keep the chain out of the dirt, and file depth gauges to the chain maker's setting.
  • Follow a five-step felling plan, cut a 70-degree notch about one-quarter of the diameter, and never cut through the hinge.
  • Plan on about 0.5 cord per acre per year of sustainable growth unless a forester measures more.
  • Check managed-forest tax programs, and get the right permit before cutting firewood on public land.

This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.

The Comprehensive Off-Grid Manual

Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.

Tools

Setting Up an Off-Grid Workshop

Plan an off-grid shop: tool power and motor start surge, daily energy use, lighting levels, wood dust and noise limits, fuel storage limits and oily rag safety.

13 min read
Tools

Private Roads, Vehicles and Winter Access

Secure legal access, build and crown a gravel road, size gravel loads, get stream crossing approvals, clear snow, meet winter tire rules and judge safe ice.

13 min read