Home › Free guides › Repairs

Field Repairs: Plumbing, Electrical and Mechanical

Tools  13 min read

On a remote property, the nearest plumber, electrician or small-engine shop may be hours away, and in winter a burst pipe or a generator that will not start cannot wait. This guide covers which repairs owners may legally do themselves and which need a permit or a licensed trade, a tool and spare-parts kit, plumbing repairs including frozen pipes and push-fit fittings, safe electrical fault-finding, small-engine and generator repair, and the habits that prevent breakdowns.

What you may do yourself

Rules on owner repairs differ by trade and by jurisdiction. Know them before you start, because unpermitted work can void insurance and cause problems when the property is sold.

Electrical

Electrical installations in Canada follow the Canadian Electrical Code, CSA C22.1, adopted with amendments by each province. In the US, the National Electrical Code (NFPA 70) is adopted by states and local governments.

  • British Columbia: homeowners can apply to Technical Safety BC for a homeowner electrical permit for work in their own home, such as installing fixtures, switches, outlets or solar equipment. A declaration is filed after each phase of work or every 180 days, and an inspection must be requested within 180 days of the permit being issued. Owners of strata units and people running a business from the home cannot get a homeowner permit.
  • Ontario: homeowners may do electrical work in their own home, but only the homeowner, not friends or family, may do it. A notification of work must be filed with the Electrical Safety Authority (ESA) before starting, even for small jobs, and ESA must review the work before it is covered up. ESA then issues a Certificate of Acceptance.
  • Elsewhere: other provinces and most US states and counties have their own homeowner permit rules. Some require licensed electricians for all work. Ask your provincial or state electrical authority.

Gas and propane

Propane and natural gas piping and appliances in Canada are covered by the Natural Gas and Propane Installation Code, CSA B149.1. Installation and repair of gas piping and appliances generally must be done by a licensed gas fitter. Owner repairs are limited to what the appliance manual says the user may do, such as relighting a pilot.

Plumbing and wells

Plumbing permits for new work and alterations are usually issued by the local building authority where inspection applies. Like-for-like repairs of a leaking fitting or a failed tap rarely need a permit. Well and well-pump work may be restricted; our guide to off-grid water covers BC's requirements for registered well pump installers.

Tools and spare parts

A breakdown on a remote property becomes an emergency when the part needed is a day's drive away. Keep spares for anything whose failure would stop water, heat or power.

SystemToolsSpares
PlumbingPipe cutter for PEX and copper, adjustable wrenches, pipe wrench, deburring tool, PEX crimp or expansion tool to match your system, thread sealant tapePush-fit couplings, tees and end caps in each pipe size; pipe repair clamps; spare length of pipe; tap washers and cartridges; filter cartridges; pressure switch
ElectricalDigital multimeter, non-contact voltage tester, insulated screwdrivers, wire strippers, crimper, headlampFuses of every rating in use, a spare breaker of each type, wire connectors, crimp terminals, heat-shrink tubing, electrical tape
EnginesSocket set, spark plug socket, feeler gauge, oil drain pan, funnel, carburettor cleanerSpark plugs, air filters, fuel filters, oil, pull-start rope, belts for anything belt-driven
GeneralCordless drill and driver, hacksaw, files, clamps, flashlight, magnifierHose clamps, epoxy putty, self-fusing silicone tape, assorted bolts, nuts and washers, cable ties

Keep a binder or folder with the manual, model number and serial number of every pump, appliance, inverter, generator and engine on the property. Record the part numbers of filters, plugs and belts. When a part fails, take a photo of it and its label before removing it.

Plumbing repairs

Stopping a leak

  1. Shut off the pump or close the main valve, then open a tap below the leak to drain pressure.
  2. Turn off the water heater if it may drain.
  3. Dry the area and find the exact source. Water runs along pipes, so the drip may be some distance from the leak.
  4. Repair it permanently if you can. If not, fit a temporary clamp and plan a proper repair.

Push-fit fittings

Push-to-connect fittings make the fastest permanent repair for most household pipe. SharkBite's fittings, for example, join copper, CPVC and PEX in copper tube sizes in any combination. The maker lists them as certified to ASSE 1061 and NSF/ANSI 61, rated to 200 psi (1,380 kPa) and 93 °C (200 °F), and approved for use underground and inside walls without access panels.

  • Cut the pipe square with a proper cutter, not a hacksaw.
  • Remove burrs from the inside and outside edge of the cut. A burr can cut the O-ring.
  • Mark the insertion depth on the pipe using the maker's gauge or chart.
  • Push the pipe in until it reaches the stop and the mark meets the fitting.
  • For PEX, use the insert stiffener if the maker specifies one.

Check that the fittings you buy are accepted under the plumbing code in your province or state. Keep the release tool or clip that removes them.

PEX crimp and expansion joints

Crimp, clamp and expansion fittings are each made for particular PEX types and need their own tools. Do not mix systems. Check each crimp with the go/no-go gauge supplied with the tool. A crimp that does not pass must be cut out and redone.

Frozen pipes

A pipe that has frozen may already be split. It will not leak until it thaws, so be ready to shut off the water.

  1. Open the tap nearest the frozen section. Flowing water shows when the pipe has thawed, and an open tap relieves pressure.
  2. Apply gentle heat: an electric heating pad, a hair dryer or a space heater kept well away from flammable materials. Start from the tap end and work back toward the ice.
  3. Once water flows, check the whole run for leaks.

To stop the same pipe freezing again, insulate it, reroute it to the warm side of the insulation, or install heat-trace cable listed for the pipe material, controlled by a thermostat. Self-regulating heat-trace draws more power as temperature falls, so include it in your winter energy budget.

Water system faults

SymptomLikely causesFirst checks
No water at any tapPump has no power, pressure switch failed, frozen line, empty cistern, tripped breaker or inverter shutdownCheck power at the pressure switch with a meter; check the breaker; check the tank level
Pump starts and stops every few secondsPressure tank waterlogged or lost its air chargeWith pump off and tank drained, check the air precharge at the tank valve
Pressure falls slowly when taps are closedLeak in the system, or a leaking check valve or foot valveClose the valve after the tank; if pressure holds, the leak is downstream
Low flow at one tapClogged aerator or cartridgeRemove and clean the aerator
Low flow at all tapsClogged sediment filterCompare pressure before and after the filter; change the cartridge
Pump runs but never shuts offLost prime (jet pump), low water level, broken pipe, worn pumpCheck for leaks and water level; reprime a jet pump per its manual

Pressure tank precharge settings and how to choose a tank are covered in our guide to off-grid water.

Electrical fault-finding

Test before you touch

The safe method is to confirm that the tester works, test the circuit, and then confirm the tester still works.

  1. Switch off the breaker or remove the fuse. Lock or tape the breaker off and leave a note.
  2. Check your voltage tester or multimeter on a circuit you know is live.
  3. Test the circuit you will work on, between every pair of conductors and from each to ground.
  4. Check the tester again on the known live circuit.

Non-contact voltage testers are useful for a quick check but can give false readings. Confirm with a multimeter before touching conductors. On an off-grid system, remember that the battery side stays live when the AC breakers are off, and solar panels produce voltage whenever light falls on them.

Common faults

  • Breaker trips at once when reset: a short circuit or ground fault. Unplug everything on the circuit and reset. If it still trips, the fault is in the wiring or a fixed appliance.
  • Breaker trips after running for a while: overload. Add up the loads on the circuit.
  • GFCI or GFI outlet trips: current leaking to ground, often from moisture in an outdoor outlet, a pump or a heat-trace cable. Dry the device, then reset. If it trips again, find the faulty device by unplugging loads one at a time.
  • Outlet or switch warm, discoloured or smelling of burning: a loose or corroded connection. Shut off the circuit and repair it before using it again.
  • Lights dim when a large load starts: normal briefly for motors, but a long or deep dip suggests undersized wire, a loose connection or an inverter at its limit.

Worked example: is the circuit overloaded?

Current (amps) = power (watts) ÷ voltage (volts).

A 120 V, 15 A circuit supplies a 1,500 W space heater and a 300 W heat-trace cable.

  • Heater: 1,500 ÷ 120 = 12.5 A
  • Heat-trace: 300 ÷ 120 = 2.5 A
  • Total: 15.0 A

Both run for hours at a time. Electrical codes generally limit continuous loads to 80% of the breaker rating: 15 A × 0.8 = 12 A. The circuit is overloaded and the breaker will trip, or the wiring will run hot. Move one load to another circuit.

The same arithmetic on a 12 V DC circuit shows why low-voltage wiring needs heavy cable: a 120 W load at 12 V draws 120 ÷ 12 = 10 A.

DC connections

In battery and solar wiring, loose or corroded connections cause most faults and can start fires, because high currents flow at low voltage. Check terminal tightness to the torque the maker specifies once a year. Look for discoloured lugs or melted insulation. Use crimped lugs made with the correct die, not twisted wire under a screw. Battery and solar system design is covered in our guides to batteries and solar power.

Small engines and generators

Engine will not start

A small engine needs three things: fuel, spark and air, plus compression. Check them in order.

  1. Basics: fuel valve open, choke set, ignition switch on, oil level correct. Many generators will not start when oil is low.
  2. Fuel: is it fresh? Gasoline left in a tank or carburettor for months goes stale and leaves gum. Drain old fuel and refill with fresh fuel.
  3. Spark: remove the plug. A wet, black or fouled plug points to flooding or a rich mixture. Clean or replace it, and set the gap to the manual's figure.
  4. Air: check that the air filter is not soaked, blocked or crushed.
  5. Carburettor: if fuel is fresh and spark is good, the carburettor jets or float bowl may be blocked with old fuel residue. Drain the float bowl; clean with carburettor cleaner, or fit a replacement carburettor.

Storing engines

Most no-start problems come from fuel left in an engine over a season. Before storing an engine for more than a month or two, add fuel stabilizer and run it through, or run the carburettor dry and drain the tank, as the manual directs. Two-stroke fuel mixing is covered in our chainsaw guide.

Generator maintenance

Follow the maintenance schedule in the generator's manual. As an example, Honda's EU2000i manual calls for checking oil before each use and changing it after the first month or 20 hours, then every 3 months or 50 hours, whichever comes first.

Worked example: planning a year of generator service

A generator backs up a solar system, running 3 hours a day for 120 days through the darkest part of the winter.

Run time: 3 × 120 = 360 hours.

At 50 hours per oil change: 360 ÷ 50 = 7.2, so about 7 oil changes in the winter, roughly one every 17 days.

With an oil capacity of 0.4 L, that is 7 × 0.4 = 2.8 L of oil; keep at least that on hand, with spare plugs and an air filter. Log hours in a notebook kept with the generator.

Temporary fixes until the part arrives

Sometimes the right part is days away. A temporary repair should be safe, should be easy to see, and should be replaced as soon as possible. Write it in the log so it is not forgotten.

  • Split pipe: a stainless pipe repair clamp with a rubber liner, sized to the pipe's outside diameter, holds household pressure. Centre the liner over the split and tighten the bolts evenly.
  • Pinhole in a drain or vent: epoxy putty works on unpressurized pipe that has been dried and roughened. It is not a lasting repair on a pressure line.
  • Weeping threaded joint: self-fusing silicone tape wrapped tightly under tension can slow a small leak on a low-pressure line until the joint can be remade.
  • Split hose on an engine or pump: cut out the damaged section and join the ends with a barbed connector of the same inside diameter and two hose clamps.
  • Blown fuse: replace it only with one of the same type and rating. A fuse that blows again points to a fault. A larger fuse or a bypass removes the protection for the wire and can start a fire.
  • Broken wire: join it with a connector or crimp splice rated for the wire size and current, insulate it with heat-shrink tubing, and keep it dry.

Do not improvise on anything carrying gas, propane, fuel lines under pressure, brakes, steering or structural loads. Those wait for the correct part.

Preventing breakdowns

  • Keep a log of every repair, part, filter change and service, with dates and hours.
  • Walk the systems monthly: look for drips under pipes and fittings, listen to the pump cycle, read battery and inverter displays, and check for warm or discoloured connections.
  • Exercise standby equipment: start the backup generator and run it under load monthly, and open and close valves that are rarely used so they do not seize.
  • Service before the season: service generators, snow equipment and heating before winter, and pumps and water systems before the cabin is opened in spring.
  • Label everything: breakers, shut-off valves, pipes and disconnects. Anyone in the house should be able to shut off water and power in an emergency.
  • Replace on age: filters, pressure switches and pump capacitors are cheap compared with the damage from a failure in January.

Learn your limits. A repair done wrongly can cost more than calling a trade, especially when it involves gas, a service panel, a well or a structural member. Build a list of local tradespeople who will travel to your area, before you need them.

Key points

  • Check homeowner permit rules before electrical, plumbing or gas work; in BC and Ontario, owners may do their own electrical work under a homeowner permit or ESA notification.
  • Gas and propane piping and appliances generally require a licensed gas fitter.
  • Stock spares for anything whose failure stops water, heat or power, and keep manuals and part numbers together.
  • Cut and deburr pipe cleanly and mark insertion depth before using push-fit fittings.
  • Thaw frozen pipes with gentle electric heat from the tap end. Never use an open flame.
  • Test circuits dead with a meter checked on a live circuit before and after; keep continuous loads under 80% of breaker rating.
  • Stale fuel causes most small-engine failures. Follow the generator's oil schedule and log run hours.
  • Run generators outdoors, at least 6 m (20 ft) from the house, and never backfeed house wiring.

This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.

The Comprehensive Off-Grid Manual

Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.

Tools

Setting Up an Off-Grid Workshop

Plan an off-grid shop: tool power and motor start surge, daily energy use, lighting levels, wood dust and noise limits, fuel storage limits and oily rag safety.

13 min read
Tools

Private Roads, Vehicles and Winter Access

Secure legal access, build and crown a gravel road, size gravel loads, get stream crossing approvals, clear snow, meet winter tire rules and judge safe ice.

13 min read