On a private well, spring, lake intake or cistern, nobody tests the water unless the owner does, and nobody fixes it unless the owner chooses the right treatment. This guide covers when and how to test, how to take a sample the lab can use, how to read bacteria results and a chemical report against the Canadian guidelines, how to match treatment equipment to the problem with the right certification, what treatment costs in water and power off the grid, and how to disinfect a well after a positive result.
When to test
Health Canada recommends testing a private well for bacteria (E. coli and total coliforms) at least every 6 months, and for general water quality every 2 years. How often to test for particular chemicals depends on local geology and land use; your local public health authority can advise which ones matter in your area.
Test as well:
- in early spring and in fall;
- after heavy rain, flooding, a long dry spell or a wildfire;
- after the well has been out of use for a long time, such as when reopening a seasonal cabin;
- after any repair or maintenance on the well, pump or plumbing;
- when land use nearby changes, such as new livestock, a new septic field or fuel storage;
- whenever the water changes in colour, taste or smell.
Health Canada advises testing more often if the well is dug, is in bedrock, has only a thin layer of soil over it, or has less than 25 m (82 ft) of casing. Surface water, springs and rainwater cisterns are more exposed than any well and should be tested at least as often, even when treatment is installed, to confirm the treatment is working.
What to test for
| Test group | Parameters (Health Canada list) | When |
|---|---|---|
| Microbial | E. coli and total coliforms | At least every 6 months, and after events listed above |
| Common chemicals | Arsenic, copper, lead, manganese, nitrate and nitrite, uranium | When the well is new or you buy the property, then as local health authorities advise |
| General water quality | pH, iron, chloride, alkalinity, ammonia, hardness, sodium, sulphate, total dissolved solids, dissolved organic carbon | Every 2 years |
| Situational | Volatile organic compounds, hydrocarbons, pesticides, heavy metals, PFAS | After a fire or fuel spill, or near industrial, agricultural or contaminated sites |
Use a laboratory accredited for drinking water analysis. Your provincial or territorial drinking water authority or public health unit can direct you to one; in some provinces the public health system tests private well water for bacteria. Public Health Ontario, for example, tests private drinking water from wells, cisterns and treated lake water for total coliforms and E. coli, but not for chemicals. A clean bacteria result says nothing about arsenic, uranium or nitrate.
Taking a bacteria sample
A careless sample gives a false result, usually a false positive that costs a round of retesting. Ontario's instructions for E. coli and coliform samples are a good standard procedure:
- Get a sterile bottle from the laboratory. If its seal is broken, get another.
- Label the bottle before sampling, as the lab directs.
- Do not add bleach to the well beforehand; the sample must represent the water you normally drink.
- Wash your hands or put on clean disposable gloves.
- Run a cold tap for 2 to 5 minutes, until the water is cold.
- Do not rinse the bottle. It contains a preservative.
- Do not touch the inside of the bottle, its lip or the inside of the cap, and do not set the cap face down.
- Reduce the flow so it does not splash, fill to the fill line (or the shoulder) without overflowing, and cap it at once.
- Keep the sample at 4 to 10 °C without freezing it, using ice packs rather than loose ice.
- Deliver it as soon as possible, preferably within 24 hours. Ontario's instructions say bacteria testing must begin within 24 hours; Public Health Ontario accepts samples tested within 48 hours of collection. Check the lab's drop-off hours before sampling.
Reading bacteria results
Health Canada's guideline is no detectable E. coli and no detectable total coliforms per 100 mL in non-disinfected groundwater. Public Health Ontario reports results in colony-forming units (CFU) per 100 mL and interprets them this way:
| Total coliforms | E. coli | Public Health Ontario interpretation |
|---|---|---|
| 5 or fewer | 0 | No significant contamination; keep testing regularly |
| More than 5 | 0 | Significant bacterial contamination; stop using the well, contact your health unit and resample |
| Any | 1 or more | Unsafe: fecal contamination from human or animal waste; stop using the well, contact your health unit and resample |
| Overgrown with other bacteria | No result possible; treat the water as unsafe and resample | |
Health Canada advises that if E. coli is found, the water is not safe: boil water for drinking, cooking and brushing teeth, or use another safe supply. If only total coliforms are found, more information is needed; retest as soon as possible. If a second or third test confirms contamination, shock-disinfect the well and find the cause, which is often a damaged cap, a buried wellhead, surface water ponding around the casing or a nearby septic problem.
Reading a chemical report
Lab reports list each parameter with its result and the guideline value. Health Canada sets two kinds of value: a maximum acceptable concentration (MAC) where a substance affects health, and an aesthetic objective (AO) where it affects taste, smell, colour or staining. Our guide to water systems lists the MACs for arsenic, uranium, manganese, nitrate, lead and fluoride. Others that appear on well reports:
| Health-based parameter | Health Canada MAC |
|---|---|
| Nitrite | 1 mg/L as nitrite-nitrogen (3 mg/L as nitrite) |
| Nitrate | 10 mg/L as nitrate-nitrogen (45 mg/L as nitrate) |
| Barium | 2.0 mg/L |
| Boron | 5 mg/L |
| Selenium | 0.05 mg/L |
| Copper | 2 mg/L (aesthetic objective 1 mg/L) |
Check the units on nitrate: a result of 30 mg/L reported "as nitrate" is below the 45 mg/L MAC, but the same number "as nitrate-nitrogen" is three times the 10 mg/L MAC.
| Aesthetic parameter | Health Canada value | What you notice |
|---|---|---|
| Iron | AO ≤ 0.1 mg/L | Orange-brown staining, metallic taste, discoloured laundry |
| Manganese | AO ≤ 0.02 mg/L | Black or brown staining and deposits |
| Hydrogen sulphide | AO ≤ 0.05 mg/L | Rotten-egg smell, tarnished silver and copper |
| Chloride | AO ≤ 250 mg/L | Salty taste, corrosion |
| Sulphate | AO ≤ 500 mg/L | Bitter taste, laxative effect |
| Sodium | AO ≤ 200 mg/L | Salty taste |
| Total dissolved solids | AO ≤ 500 mg/L | Taste, scaling |
| Colour | AO ≤ 15 TCU | Tea-coloured water, often from organic matter |
| Zinc | AO ≤ 5.0 mg/L | Taste |
| pH | 7.0 to 10.5 | Low pH corrodes copper and lead from plumbing |
| Hardness | No guideline; above 200 mg/L considered poor, above 500 mg/L generally unacceptable | Scale, poor lathering, softener needed |
Health Canada notes that discoloured water should prompt testing for iron and other metals, because iron deposits can carry arsenic, lead and manganese with them.
Hardness units
Labs usually report hardness in mg/L as calcium carbonate. Softener makers often use grains per gallon (gpg). One grain per US gallon equals 17.1 mg/L, so a result of 300 mg/L is 300 ÷ 17.1 = 17.5 gpg.
Metals from plumbing
Copper and lead in tap water usually come from the plumbing, not the aquifer. Water with a low pH, below Health Canada's range of 7.0 to 10.5, dissolves copper pipe, brass fittings and old lead solder, especially where water sits in the pipes overnight or for weeks in a seasonal cabin. Blue-green staining under taps and a metallic taste are signs of copper corrosion.
To find where metals come from, ask the lab for two samples: a first-draw sample taken after the water has stood in the pipes for several hours, and a sample taken after running the tap until the water is cold. A first-draw result much higher than the flushed result points to the plumbing. Until the cause is fixed, run the tap until cold before drawing drinking water, and use only cold water for drinking and cooking. Fixes include replacing lead-bearing parts and treating corrosive water, as a treatment dealer can advise from the lab report; Health Canada publishes guidance on choosing a filter certified for lead.
Keeping records
Keep every lab report in one file with the well record, treatment equipment manuals and service dates. A single result shows the water on one day; a series of results shows trends. A nitrate result creeping up from one test to the next, or coliforms appearing every spring, points to a cause that a single test cannot reveal. Records also show a buyer, lender or insurer that the supply has been looked after, and give a treatment dealer the history needed to size equipment correctly.
Matching treatment to the problem
Health Canada's advice is to fix the source of contamination where possible, then, if treatment is needed, to choose a device certified to the NSF/ANSI standard that covers your specific contaminant, and to check the maker's documentation for exactly what it is certified to remove. Certification to a standard does not mean a device removes every contaminant that standard can cover.
| Standard | Technology | What it treats (Health Canada summary) | Notes |
|---|---|---|---|
| NSF/ANSI 42 | Filtration | Aesthetic problems: chlorine, taste, odour, particles, manganese | Not a health claim |
| NSF/ANSI 53 | Filtration, usually carbon | Protozoa, arsenic V, lead, copper | Removes only arsenic V |
| NSF/ANSI 44 | Cation exchange softener | Hardness (calcium, magnesium) | Adds sodium or potassium |
| NSF/ANSI 55 Class A | Ultraviolet light | Bacteria, viruses, protozoa | Particles block UV; pre-filter |
| NSF/ANSI 58 | Reverse osmosis | Protozoa, nitrate, nitrite, arsenic V, lead, copper | Removes only arsenic V; usually one tap |
| NSF/ANSI 62 | Distillation | Bacteria, viruses, protozoa, nitrate, nitrite, arsenic, lead, copper, manganese | Slow, high energy use |
| NSF/ANSI 401 | Various | Selected emerging contaminants | Check the specific claim |
Point of use or point of entry
A point-of-entry system treats all water entering the building. A point-of-use system treats water at one tap, usually the kitchen. Contaminants that harm through drinking, such as arsenic, nitrate and uranium, can be handled at one tap; problems that affect the whole house, such as bacteria, iron staining, hardness and sulphide smell, need point-of-entry treatment.
Common problems and approaches
- Bacteria: find and fix the source first. Where a supply stays vulnerable, as with surface water or a dug well, continuous disinfection is needed: a UV unit certified to NSF/ANSI 55 Class A, or chlorine, hydrogen peroxide or ozone systems with routine monitoring of the residual. Alberta's guidance notes that pellet chlorinators placed over the wellhead are not appropriate continuous disinfection.
- Arsenic: ask the lab whether the arsenic is arsenic III or arsenic V. Certified filters and reverse osmosis units remove only arsenic V; arsenic III needs a pre-treatment step or equipment certified for it, which a treatment dealer can specify from the lab result.
- Nitrate: reverse osmosis or distillation at the drinking tap. Nitrate signals that surface pollution, often manure, fertilizer or septic effluent, is reaching the aquifer, so look for the source.
- Iron and manganese: Alberta's guidance describes oxidizing filters such as manganese greensand, regenerated with potassium permanganate, and air injection followed by filtration. Health Canada notes that certified residential iron-removal units currently rely on adsorption, and that other methods are expected to work but are not certified for iron. Remove iron and manganese before UV or reverse osmosis, which they foul.
- Hydrogen sulphide: aeration releases the gas, which must be vented outdoors.
- Hardness: a softener certified to NSF/ANSI 44. Health Canada recommends leaving the kitchen tap on unsoftened water for drinking and cooking because the softener adds sodium.
- Sodium and dissolved solids: reverse osmosis or distillation.
- Taste and odour: activated carbon. Alberta's guidance warns that carbon filters can grow bacteria if not maintained.
Put treatment in order so each stage protects the next: sediment filtration, then iron and manganese removal, then softening, then disinfection last, with reverse osmosis at the drinking tap where needed.
Treatment costs in water and power
Off the grid, the choice between treatment methods often comes down to how much water and electricity each uses.
Worked example: reverse osmosis waste water
Alberta's guidance states that small reverse osmosis systems send 3 to 20 L to drain for every litre of treated water. A household treating 10 L a day for drinking and cooking therefore sends 30 to 200 L a day to drain. From a low-yield well or a cistern holding 12,000 L, 200 L a day is significant, and it adds load to the septic system. Compare the waste ratio of certified units before buying.
Worked example: distiller energy
Heating water from cold and boiling it takes about 2.6 MJ per kilogram. One litre of distilled water therefore needs about 2.6 MJ, or 2.6 ÷ 3.6 = 0.72 kWh, before any losses.
Ten litres a day needs at least 7.2 kWh a day, more than many off-grid cabins use for everything else in winter. Alberta's guidance notes that distillation is generally used only for small quantities of drinking and cooking water because of its power use, scaling and slow output. Reverse osmosis or certified filters are far cheaper to run off the grid; distillation suits only a property with surplus summer solar or a wood cookstove kettle.
Worked example: sizing a softener
A household of four uses 600 L (158 US gal) a day. Hardness is 300 mg/L, or 17.5 gpg.
Hardness removed per day: 17.5 × 158 = 2,765 grains. For a regeneration every 7 days, the softener must remove 2,765 × 7 = 19,355 grains between regenerations.
Choose a unit whose rated capacity at the salt setting you intend to use exceeds about 19,400 grains. Each regeneration backwashes resin and brine to drain; Alberta's guidance warns that this backwash water can overload a septic system, so ask the installer where it should discharge.
Shock disinfection after a positive result
Health Canada publishes a shock disinfection procedure and bleach quantities for unscented 5.25% household bleach. For an existing 15 cm (6 in) drilled well, the table gives 20 mL of bleach per metre of water depth, which produces about 50 mg/L of chlorine; for a new drilled well, 100 mL per metre (about 250 mg/L). For an existing 90 cm (36 in) dug well it gives 0.6 L per metre.
Worked example: bleach for an existing drilled well
Total depth 60 m, static water level 15 m: water depth is 60 − 15 = 45 m. Bleach needed: 45 × 20 mL = 900 mL of 5.25% unscented bleach.
The procedure, in summary:
- Bypass softeners, filters and reverse osmosis units, which chlorine can damage.
- Turn off the pump, remove the well cap, and pour the bleach in with a funnel, keeping it off electrical connections.
- Restore power. Run a hose from the nearest outdoor tap back into the casing for 30 minutes to mix the water, directing any discharge away from wells, septic systems, plants and surface water.
- Open each indoor hot and cold tap, including showers and toilets, until chlorine smell is strong, then close it.
- Let the water stand 12 to 24 hours without using it.
- Flush the well through an outdoor hose, then the indoor taps, until the smell is gone, keeping the water away from surface water and the septic system.
- Sample 48 hours after treatment. Boil drinking water for 1 minute at a rolling boil until results come back safe.
Treatment has likely worked after two consecutive safe results over 1 to 3 weeks; test once more 3 to 4 months later. If results stay positive, repeat the disinfection, inspect the well and property for a contamination source, and contact your public health unit. Clean treatment devices as their makers direct before reconnecting them.
Key points
- Test for E. coli and total coliforms at least every 6 months, general chemistry every 2 years, and after floods, repairs, long disuse or any change in the water.
- Use an accredited lab's sterile bottle, do not rinse it, keep the sample at 4 to 10 °C and deliver it within 24 hours.
- Any E. coli means the water is unsafe: boil it or use another source, retest, and shock-disinfect if confirmed.
- Read MACs for health and AOs for nuisance problems; check whether nitrate is reported as nitrate or as nitrogen. Iron's AO is now 0.1 mg/L.
- Choose devices certified to the NSF/ANSI standard for your contaminant, and test before and after treatment to confirm it works.
- Certified filters and reverse osmosis remove only arsenic V; ask which form you have.
- Off the grid, count reverse osmosis waste water (3 to 20 L per litre) and distiller energy (over 0.7 kWh per litre).
This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.
The Comprehensive Off-Grid Manual
Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.
More guides
Off-Grid Water: Wells, Rainwater and Treatment
Size a cistern from roof area and rainfall, choose wells, pumps and pressure tanks, treat and test water, and winterize an off-grid system.
Water Rights and Licensing for Wells, Springs and Streams
Who controls water in Canada, BC licensing rules as a worked model, scarcity limits, instream work approvals, US water law and checks for buyers of rural land.
Drilled and Dug Wells: Siting, Construction and Yield
Site a drilled or dug well under Canadian and US rules, learn how casing and seals work, read a yield test, meet peak demand and decommission old wells.