Home › Free guides › Atlantic

Off-Grid Living in Nova Scotia, PEI, Newfoundland and Labrador

Regions  12 min read

Nova Scotia, Prince Edward Island, Newfoundland and Labrador have a maritime climate: winters milder than inland Canada but wet, windy and changeable, with heavy snow in western Newfoundland and Labrador, salt air on every coast and strong post-tropical storms in autumn. This guide covers design temperatures, snow and wind loads, foundations, the solar resource by month, each province's rules for wells, septic systems, development permits and burning, land status in Labrador's Inuit settlement area, storm, flood and wildfire risk, and practical system choices.

Design climate

The table gives heating design temperatures and heating degree-days from the NOAA Engineering Weather Data record for 1973 to 1993 (Halifax) and 1973 to 1996 (Gander), converted from Fahrenheit. They are annual percentile values, not the National Building Code's January 2.5% values; use the code or the building authority's values for design.

Location99% heating design temperature99.6% heating design temperatureHeating degree-days (about, below 18 °C)
Halifax, NS−17 °C (1 °F)−19 °C (−2 °F)4,520
Gander, NL−18 °C (0 °F)−20 °C (−4 °F)5,390

Design cold is moderate, but the heating season is long. Gander's design temperature is only a degree below Halifax's, yet it has about 5,390 ÷ 4,520 = 1.19 times the heating degree-days, because its cool season is longer. Cool, damp summers also mean that buildings and firewood dry slowly.

Snow and wind loads

The values below are the 2010 National Building Code figures as reproduced in a 2014 Boise Cascade specifier guide. Current code values may differ; confirm them with the building authority.

LocationSs (ground snow)Sr (rain on snow)Hourly wind pressure q (1-in-50)
Halifax (Dartmouth), NS1.6 kPa0.6 kPa0.58 kPa
Sydney, NS2.3 kPa0.6 kPa0.59 kPa
Charlottetown, PE2.7 kPa0.6 kPa0.56 kPa
St. John's, NL2.9 kPa0.7 kPa0.78 kPa
Gander, NL3.7 kPa0.6 kPa0.60 kPa
Corner Brook, NL3.7 kPa0.6 kPa0.55 kPa
Happy Valley-Goose Bay, NL5.3 kPa0.4 kPa0.42 kPa

Two features stand out. Rain-on-snow loads of 0.6 to 0.7 kPa are among the highest in Canada, because winter rain falls on existing snow and soaks it. And St. John's has the highest reference wind pressure in this table, 0.78 kPa, compared with 0.42 kPa at Goose Bay.

Worked example: rain on snow

A roof footprint of 8 m × 10 m (26 ft × 33 ft), 80 m² (861 sq ft), near Gander.

Ground snow alone: 3.7 × 80 = 296 kN, about 30 tonnes. The rain-on-snow allowance adds 0.6 × 80 = 48 kN, about 4.9 tonnes, to the design value. That extra 4.9 tonnes is the weight of 4,900 L of water held in the snowpack, the same as 61 mm (2.4 in) of rain soaked into snow over the whole roof (4,900 L ÷ 80 m² = 61 L/m²).

Wet snow does not slide off as readily as dry snow, and roof drains and gutters freeze. Keep roof valleys and drains clear, and do not let ice dams build at the eaves.

Foundations and frost

Atlantic soils range from bare rock and glacial till in Newfoundland and much of Nova Scotia to the red sandstone-derived soils of Prince Edward Island. Under Part 9 of the National Building Code (Table 9.12.2.2), footings on rock need no minimum depth. On clay or soils not clearly defined they need at least 1.2 m (3 ft 11 in) of cover, and under a building with no heated space they must also be below the depth of frost penetration. Ask the building authority what frost depth it uses.

Repeated freezing and thawing through a maritime winter is hard on shallow footings, concrete and masonry. Pier footings on till should go below frost depth or onto rock. Provide drainage around foundations, since water-saturated ground heaves more than dry ground.

Solar resource by month

The table gives calculated day length and noon sun height on the 21st of each month at Halifax, 44.7° N. St. John's, at 47.6° N, has about 25 minutes less daylight in December and a noon sun of 19°. Happy Valley-Goose Bay, at 53.3° N, has 7.5 hours of daylight in December and a noon sun of 13°.

Month (21st)Day lengthNoon sun height
January9.3 h25°
February10.7 h34°
March12.1 h45°
April13.7 h57°
May15.0 h65°
June15.6 h69°
July15.1 h66°
August13.7 h57°
September12.1 h45°
October10.6 h34°
November9.3 h25°
December8.8 h22°

Cloud, fog and drizzle are frequent, especially on the Avalon Peninsula and the Atlantic shore of Nova Scotia. A Canada Energy Regulator comparison of large Canadian cities ranked St. John's lowest for solar potential, with Halifax also in the lower half. A Natural Resources Canada study of rooftop solar found average yields across all roof surfaces of about 796 kWh per kW of panels per year in Halifax and 741 kWh/kW in St. John's. These are still usable figures: solar works here, but needs more panels per kilowatt-hour than on the Prairies. Natural Resources Canada's photovoltaic potential maps give monthly values for more than 3,500 municipalities.

Worked example: how much more solar?

A household needs 3,000 kWh a year from solar. Using the Natural Resources Canada average rooftop yields:

  • Halifax, 796 kWh/kW: 3,000 ÷ 796 = 3.8 kW of panels.
  • St. John's, 741 kWh/kW: 3,000 ÷ 741 = 4.0 kW.
  • Winnipeg, 857 kWh/kW: 3,000 ÷ 857 = 3.5 kW.

The difference over a year is modest. The winter difference is larger, because fog and storm cloud are worst when days are shortest, so battery and generator sizing matter more here than array size.

Wind is the region's other large energy resource. An exposed coastal site can suit a small turbine, which produces most in the stormy months when solar is weakest. The tower and foundation must be designed for the local wind pressure, and the turbine must be able to shut down safely in a storm.

Nova Scotia rules

Wells

Nova Scotia's Well Construction Regulations require a certificate to drill a well (well driller) or to construct a dug well (well digger) for others. An owner may dig, repair or decommission a dug well on land the owner owns or leases without a certificate, but must notify the Department at least 24 hours before starting and must meet the same construction standards. Casings for both drilled and dug wells must extend at least 152 mm (6 in) above the ground.

The regulations set minimum distances from a well to sources of contamination. Some of the main ones:

FromDrilled wellDug well
Cesspool61 m (200 ft)61 m (200 ft)
On-site sewage disposal system15.2 m (50 ft)30.5 m (100 ft)
Above-ground petroleum tank, 1,200 L or less5 m (16 ft)15.2 m (50 ft)
Underground petroleum tank15.2 m (50 ft)15.2 m (50 ft)
Public road or highway (outer boundary)6.1 m (20 ft)6.1 m (20 ft)
Landfill or former dump61 m (200 ft)61 m (200 ft)

Wells may not be built in basements unless the Minister accepts another location. A well construction record, including GPS coordinates, casing details, depth, clearance distances and a basic yield test, goes to the owner, and the original to the Department by January 31 of the following year. Keep the owner's copy with the property records.

Worked example: fitting a well and septic field on a narrow lot

A rural lot is 30 m (98 ft) wide and 120 m (394 ft) deep, with the house near the road. The owner wants a dug well because the previous owner had one.

A dug well must be at least 30.5 m (100 ft) from an on-site sewage system. Placed side by side across a 30 m wide lot, the two can never be far enough apart, so they must be spaced along the lot's depth: for example, the well 20 m from the road and the disposal field starting 30.5 m beyond it, at 50.5 m. The well must also be 6.1 m from the road boundary and, from an above-ground heating oil tank of 1,200 L or less, 5 m for a drilled well or 15.2 m for a dug well.

A drilled well needs only 15.2 m (50 ft) from the sewage system, which leaves more room for the house, driveway and field. The neighbours' wells and septic fields also count: a sewage system next door that sits close to the shared boundary uses up part of the separation.

Septic systems

Installing an on-site sewage disposal system in Nova Scotia requires an approval from the Department of Environment and Climate Change under the On-site Sewage Disposal Systems Regulations. The application must be supported by a site assessment and a system selection or design by a qualified person recognized by the Department. The fee is $66.35. Complete applications are usually processed in 5 to 10 business days, and an approval is valid for 3 years.

Burning

During wildfire season, Nova Scotia's daily burn restrictions apply to all open fires on private property, including backyard campfires, fire pits, chimineas, burn barrels and brush burning, and to campgrounds. Gas and charcoal barbecues and CSA-approved appliances are not covered. The BurnSafe map is updated daily at 2 p.m.:

  • Red: no open fires. The map is always red from 8 a.m. to 2 p.m.
  • Yellow: open fires only after 7 p.m.
  • Green: open fires after 2 p.m.

Fires must be out by 8 a.m. the next day. Municipal rules can be stricter. Violating daily restrictions can bring a $25,000 fine. Check the map online or at 1-855-564-2876, and report wildfires to 1-800-565-2224 or 911.

Prince Edward Island rules

Outside municipalities that have their own official plan and bylaws, the province issues development permits through Access PEI offices in Charlottetown, Montague, O'Leary and Summerside, or online. A permit is needed to start any building, place or move a building on a lot, make structural alterations that change its outside dimensions, change its use, or park a travel trailer outside a serviced trailer park. Decks, porches, garages and storage buildings also need one. Building permits confirming compliance with the National Building Code are issued under the provincial Building Codes Act.

A new or replacement on-site sewage system needs a site suitability assessment by a qualified site assessor or consulting engineer, done where the system will go. A licensed septic contractor submits a Sewage Disposal System Registered Document before development proceeds. Site plans must show distances from wetlands, watercourses, the top of any bank and sand dunes.

Newfoundland and Labrador rules

A building lot in an unserviced area must be approved for both the sewage disposal system and the well before installation. Plot plans and specifications are prepared by an Approved Designer and sent to the Government Service Centre. The application includes a site plan, floor plan, percolation test results, groundwater table depth, septic design calculations, construction drawings, a land profile and municipal approval where the lot is in a municipality. There is no fee for systems under 4,546 L (1,000 imperial gal) a day. The rules come from the Sanitation Regulations, the Environmental Control Water and Sewage Regulations, 2003, the Well Drilling Regulations, 2003 and the Water Resources Act.

Labrador Inuit lands

The Labrador Inuit Land Claims Agreement came into effect on December 1, 2005. The Labrador Inuit Settlement Area covers 72,520 km² of land and an adjacent 45,690 km² ocean zone, and includes Labrador Inuit Lands and Torngat Mountains National Park. Labrador Inuit Lands, 15,800 km², are owned by Inuit. People who are not beneficiaries of the agreement need a permit from the Nunatsiavut Government for any activity on Labrador Inuit Lands, except where the agreement already provides for their interests. Anyone considering a cabin, camp or other use in northern Labrador should contact the Nunatsiavut Government before making plans.

Labrador's climate

Inland Labrador is far colder and snowier than the island. Happy Valley-Goose Bay's ground snow load of 5.3 kPa is more than three times Halifax's 1.6 kPa: over a 48 m² (517 sq ft) cabin roof footprint, 5.3 × 48 = 254 kN, about 26 tonnes. With a December noon sun 13° above the horizon and 7.5 hours of daylight, winter solar there is closer to northern Prairie conditions than to the Maritimes. Plan heat, fuel and power as for a subarctic site.

Land and access

  • Old titles: rural land in all three provinces often has old, unsurveyed or poorly described boundaries. Commission a survey and have a lawyer check title and access before buying.
  • Shore and coastal land: coastal erosion and rising water levels are moving shorelines inland in many places. Set buildings well back from eroding banks and dunes; PEI's permit process already asks for distances to these features.
  • First Nations reserves: Mi'kmaq and other First Nations reserve lands have their own land rules. Confirm the status of any parcel through the provincial land registry.
  • Roads: many cottage and woodlot roads are private or unmaintained in winter. Confirm legal access and who ploughs it, and whether a shared road has a written maintenance agreement among the owners who use it.

Storms, flooding and wildfire

  • Post-tropical storms: autumn storms bring hurricane-force gusts, storm surge and heavy rain. Anchor roofs, solar racks and small buildings for wind uplift, and keep the area around buildings clear of trees that could fall on them.
  • Storm surge and coastal flooding: keep wells, fuel tanks, battery rooms and septic fields above the highest storm water levels, not just the normal high tide.
  • Power outages: storms can cut grid power for days. Off-grid systems avoid that, but need their own spare parts, fuel and a way to clear the access road.
  • Freezing rain: maritime winters bring frequent freezing rain. Ice on panels and turbine blades stops output and adds weight; ice on lines and trees brings them down. Size racks for ice as well as snow, and plan a safe way to clear a ground-mounted array.
  • Thaw floods: winter rain on frozen ground runs off rather than soaking in. Keep culverts and ditches on the access road clear before winter, and grade the ground so water flows away from wells and buildings.
  • Wildfire: dry springs before green-up and dry summers bring wildfire to Nova Scotia's and Newfoundland's forests. Keep firewood, fuel and brush piles away from buildings, follow the daily burn restrictions, and plan an exit route.

Before a storm

  1. Check the forecast track and timing, and finish outdoor work a day ahead.
  2. Fill fuel for the generator, vehicles and chainsaw, and top up stored water.
  3. Charge batteries fully, and reduce loads so they last if the next days are dark.
  4. Secure or bring in loose items, and check solar rack and turbine fasteners.
  5. Set a turbine to its storm or shutdown mode if the maker specifies one.
  6. Move vehicles away from trees, and keep the access road clear so you can leave or clear it afterward.

Practical system choices

  • Heat: wood is widely used; the damp climate makes covered, well-ventilated firewood storage essential. The wood heat guide explains seasoning and moisture testing.
  • Power: combine solar with a small wind turbine on exposed sites, and keep a generator for the darkest weeks.
  • Corrosion: salt air reaches far inland. Use stainless or hot-dip galvanized fasteners and racks, sealed electrical enclosures and marine-grade connectors, and rinse panels after salt-laden storms.
  • Moisture: fog, drizzle and wind-driven rain demand rainscreen cladding, good flashing and a ventilated roof. Unheated buildings should be vented to stop condensation.
  • Water: many sites rely on dug wells or springs, which are vulnerable to surface contamination; test often, and see the water systems guide for treatment.

Northern US equivalents

Coastal Maine has the same maritime climate. Septic design and well rules there are set by the state, and towns issue building permits. Ask the town office about frost depth, snow load and shoreland zoning before buying land.

Key points

  • Design cold is moderate (about −17 to −20 °C), but the heating season is long and summers are cool and damp.
  • Rain-on-snow loads are high (0.6 to 0.7 kPa), and ground snow reaches 3.7 kPa in western Newfoundland and 5.3 kPa at Goose Bay.
  • St. John's reference wind pressure, 0.78 kPa, is high. Design for wind uplift and salt corrosion.
  • Solar yields are lower than inland but usable; wind and a generator fill winter gaps.
  • Nova Scotia: certified well drillers and diggers, owner-dug wells with 24 hours' notice, and set distances from septic systems and fuel tanks.
  • PEI: provincial development permits outside planned municipalities and a qualified site assessment for septic systems. Newfoundland and Labrador: lot approval by an Approved Designer for sewage and well.
  • In northern Labrador, non-beneficiaries need a Nunatsiavut Government permit for any activity on Labrador Inuit Lands.

This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.

The Comprehensive Off-Grid Manual

Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.

Regions

Off-Grid Living on the Prairies

Prairie design cold, snow and wind loads, frost depth, solar by month, Saskatchewan and Manitoba septic and burning rules, dugouts, floods and systems.

12 min read