The Northwest Territories and Nunavut cover a third of Canada, from the boreal forest around Great Slave Lake to the treeless Arctic islands. Winters are long and extremely cold, permafrost underlies most of the land, and almost all land outside communities is either public land or land owned under modern land claim agreements. This guide covers design temperatures, snow and wind, the solar resource including polar night, foundations on permafrost, Nunavut's building guidance, sanitation and burning rules, land status and permits in both territories, wildfire and flood risk, and practical system choices.
Design climate
The table gives heating design temperatures and heating degree-days from the NOAA Engineering Weather Data record for 1973 to 1996, converted from Fahrenheit. Shepherd Bay is a weather station at 68.8° N in Nunavut's Kitikmeot Region. These are annual percentile values; use the National Building Code values or those given by the territorial authority for design.
| Location | 99% heating design temperature | 99.6% heating design temperature | Heating degree-days (about, below 18 °C) |
|---|---|---|---|
| Yellowknife, NT | −39 °C (−38 °F) | −41 °C (−42 °F) | 8,430 |
| Shepherd Bay, NU | −44 °C (−47 °F) | −45 °C (−49 °F) | 11,900 |
Yellowknife has about three times Victoria's heating degree-days, and the high Arctic about four and a half times. The Government of Nunavut's Good Building Practices Guidelines describe a design range of about −45 °C in winter to +35 °C in summer, with hourly wind pressures of 0.30 to 0.80 kPa.
Worked example: heat for a small Arctic building
A 40 m² (430 sq ft) cabin loses 80 W for every 1 °C of difference between inside and outside, and is kept at 18 °C.
At −45 °C, the difference is 63 °C: 80 × 63 = 5,040 W, about 5 kW (17,200 BTU/h).
Over a year at 11,900 degree-days: 80 × 11,900 × 24 = 22,850,000 Wh, about 22,800 kWh. Halving the heat-loss rate to 40 W per 1 °C halves that to about 11,400 kWh. Fuel reaches many northern sites only by sealift, winter road or air, so a well-insulated building saves on both fuel cost and the number of deliveries.
Snow and wind
Arctic snowfall is light, but the wind packs and drifts it. The 2010 National Building Code values, as reproduced in a 2014 Boise Cascade specifier guide, are:
| Location | Ss (ground snow) | Sr (rain on snow) | Hourly wind pressure q (1-in-50) |
|---|---|---|---|
| Yellowknife, NT | 2.2 kPa | 0.1 kPa | 0.47 kPa |
| Inuvik, NT | 2.3 kPa | 0.1 kPa | 0.48 kPa |
| Iqaluit, NU | 2.9 kPa | 0.2 kPa | 0.58 kPa |
| Rankin Inlet, NU | 3.0 kPa | 0.2 kPa | 0.60 kPa |
Confirm current values before designing. At Rankin Inlet, a 48 m² (517 sq ft) roof footprint carries a design ground snow of 3.0 × 48 = 144 kN, about 14.7 tonnes, before drift factors. Drifting governs many Arctic designs. Nunavut's guidelines advise against entrances at inside building corners, which collect snow, and recommend placing entrances where the prevailing winds scour the ground clear. They recommend a wind and snow accumulation study for new buildings, and treat wind deflectors and cold porches as ways to reduce snow at entries.
Solar resource and polar night
The table gives calculated day length and noon sun height on the 21st of each month at Yellowknife, 62.5° N. Iqaluit, at 63.7° N, is close to these figures: 4.3 hours of daylight in December and 20.8 hours in June.
| Month (21st) | Day length | Noon sun height |
|---|---|---|
| January | 6.4 h | 7° |
| February | 9.3 h | 16° |
| March | 12.1 h | 27° |
| April | 15.4 h | 39° |
| May | 18.3 h | 48° |
| June | 20.0 h | 51° |
| July | 18.5 h | 48° |
| August | 15.4 h | 39° |
| September | 12.2 h | 27° |
| October | 9.1 h | 16° |
| November | 6.3 h | 7° |
| December | 5.0 h | 4° |
North of the Arctic Circle, the sun does not rise at all for part of the winter. By calculation, the polar night lasts about a month at Inuvik, 68.4° N, from early December to early January, and about six weeks at Cambridge Bay, 69.1° N, from late November to mid-January. In return, the sun does not set for about eight weeks at Inuvik in early summer.
Spring is the best solar season in the North. From March to May the sun is up for long days, the air is cold and clear, and snow cover reflects extra light onto panels. A Natural Resources Canada study of rooftop solar potential found an average yield across all roof surfaces of about 701 kWh per kW of panels per year in Yellowknife, not far below southern cities. The yield is concentrated in spring and summer, and winter output is close to zero. A Canada Energy Regulator comparison of 20 large Canadian cities ranked Yellowknife sixth for solar potential, ahead of Ottawa, Montreal and Toronto; Iqaluit ranked sixteenth, ahead of Halifax, Vancouver, Whitehorse and St. John's.
Worked example: tilt for spring sun
In late March at Yellowknife the noon sun is 27° high. A panel tilted 63° from flat faces a point 27° above the horizon, square to the noon sun. A vertical panel on a south wall faces the horizon; its angle to the noon sun is 27°, and cos 27° = 0.89, so it still collects 89% of the direct beam at noon. It also gains reflected light from snow and sheds snow by itself.
Steep or wall-mounted arrays are common in the North for these reasons.
Foundations on permafrost
Permafrost underlies much of both territories. A heated building set on ice-rich frozen ground thaws it and settles. The Government of Nunavut's Good Building Practices Guidelines set out the practices used for public buildings, which apply equally to small private ones:
- Raise the building: on-grade crawl spaces are to be avoided; above-grade suspended floors with an open, ventilated space below are recommended. Screen open areas under buildings with durable metal mesh.
- Thermal break: provide a thermal break between piles and the floor structure, so heat does not travel down the piles.
- Ground cooling: larger heated buildings use induced-draft cold air systems, powered refrigeration or thermosyphons to keep the ground frozen.
- Grading: slope finished grades at least 4% away from buildings and the ground under them at least 2% toward sump points or away from the building. Finish the under-building area before construction and have drainage channels in place before spring runoff.
- Do not cut into frozen ground: avoid cutting into soils where permafrost is present, and use impermeable liners on gravel pad slopes in runoff paths.
- Utilidettes: the small service enclosures under trucked-service buildings need at least 300 mm (12 in) of clearance between the ground and their underside.
Below the tree line, the active layer is deeper and the permafrost often patchy, especially around Great Slave Lake. Have a geotechnical engineer investigate the site before designing any heated building.
Building envelope guidance
Nunavut's guidelines give benchmark insulation values in RSI (m²·K/W), with imperial R-values in brackets: floors on grade RSI 3.5 (R-20), suspended floors RSI 7.0 (R-40), walls RSI 5.6 (R-32) and roofs RSI 8.75 (R-50). The recommended maximum air leakage for air barrier systems is 1.5 air changes per hour at 50 Pa. Other recommendations include:
- Non-combustible semi-rigid mineral wool insulation.
- Sealants serviceable to −50 °C when fully cured.
- Low-slope roofs at least 4% (1:25), with two-ply torched-on modified bitumen membranes. Asphalt shingles are not recommended.
- Eave projections of 200 to 300 mm (8 to 12 in). Skylights are generally not recommended.
- Stairs and platforms, not ladders, for water, sewage and fuel fill points more than 1.5 m (5 ft) above the ground.
- Spring runoff directed away from buildings, so tank rooms do not flood and water or sewage holding tanks do not float.
Northwest Territories rules
Land
Since devolution in 2014, the Government of the Northwest Territories administers and controls about 80% of the land in the territory, and its Department of Lands manages all public land, surface and subsurface. Public land includes territorial lands, Commissioner's land, public highways and territorial protected areas.
Settlement lands selected under the comprehensive land claim agreements in the Inuvialuit, Gwich'in, Sahtu and Tłı̨chǫ regions are private lands, owned by those Indigenous governments and organizations; public land legislation does not apply to them. Municipal land is managed by community governments. The federal government kept jurisdiction over First Nation reserve lands, contaminated sites and some conservation lands after devolution. Any use of settlement land needs the owner's permission. Cabins on public land can be held under GNWT recreational leases; Indigenous leaseholders in areas where they have asserted or established harvesting rights may be eligible for a pause in collection of rent arrears. Federal guidance notes that land use permits are issued by federal authorities in the Inuvialuit Settlement Region and by the land and water boards elsewhere; confirm the current permitting authority before starting work.
Sanitation and wells
The NWT's General Sanitation Regulations, under the Public Health Act, require a well to be at least 30 m (98 ft) from any source of pollution. An outdoor toilet must be at least 30 m downstream from any well or water intake and at least 6 m (20 ft) from any building used for human habitation. Sewage effluent may not be discharged into a stream, river, lake or other water body without the written permission of the Chief Public Health Officer, who can also prohibit an outdoor toilet that is likely to endanger public health. Contact an environmental health officer before building a septic system, privy or well.
Worked example: laying out a privy and a well
A cabin sits on a lake shore with ground sloping toward the lake. The owner wants a drilled or hand-dug well and an outdoor privy.
- The privy must be at least 6 m from the cabin and at least 30 m downstream from the well. On ground sloping to the lake, downstream means downhill.
- So the well goes uphill, behind the cabin, and the privy goes at least 30 m from it, to the side or below, and at least 6 m from the cabin wall.
- The well must also be at least 30 m from any other source of pollution, such as a fuel tank, a greywater pit, a garbage burning area or a dog yard.
On a small lot these distances may not fit. Then hauled water or lake water treated before drinking may be the only safe supply.
Building
Under the NWT Fire Prevention Act, the Office of the Fire Marshal reviews construction plans and specifications and issues a written report. Community governments set building rules within their boundaries. Ask both before building.
Burning
The NWT wildfire season runs from May 1 to September 30. A burn permit is required by law: from the community government for burning inside municipal boundaries, and from the GNWT outside them. Clear flammable material within 3 m (10 ft) of the edge of a debris pile, keep piles small, keep water and a shovel on hand, and do not burn in wind or very dry conditions. A responsible adult must attend the fire until it is completely out. Report wildfires to 1-877-NWT-FIRE (698-3473).
Nunavut rules
Land
Nunavut was created on April 1, 1999, under the Nunavut Agreement. Its land is Crown land, Commissioner's land or Inuit Owned Land:
- Crown land is administered by Crown-Indigenous Relations and Northern Affairs Canada under the federal Territorial Lands Act.
- Inuit Owned Lands may include surface rights only, or surface and subsurface rights. Nunavut Tunngavik Incorporated manages subsurface minerals, and has delegated surface management to the three Regional Inuit Associations: Kitikmeot, Kivalliq and Qikiqtani. Use of Inuit Owned Lands requires their authorization.
- Commissioner's land and municipal land: within municipal boundaries, the Commissioner manages land tenure (leases, permits and licences) for the municipality's benefit and only with its consent, and municipalities have jurisdiction over land through by-laws. Land within 30.5 m (100 ft) of the high-water mark of the sea coast, navigable rivers and navigable lakes is Crown land, managed as untitled municipal land.
Projects go first to the Nunavut Planning Commission, which checks them against land use plans. The Nunavut Impact Review Board screens proposals, and the Nunavut Water Board authorizes water use and waste deposit on Crown land and Inuit Owned Lands.
Building
The current National Building Code, as adopted under Nunavut's Building Code Act and regulations, applies. The authority having jurisdiction is the Office of the Chief Building Official, within the Government of Nunavut's Safety Services. The Good Building Practices Guidelines supplement the code and do not replace it.
Planning for the dark season
Solar output during polar night is zero, and in the weeks either side it is too small to count. A cabin that uses 3 kWh a day therefore needs 3 × 31 = 93 kWh in December from a generator or other source, in addition to heat.
Worked example: generator charging in December
A cabin's batteries can deliver 9 kWh before they reach the lowest charge the maker allows, which covers 9 ÷ 3 = 3 days. A charger delivers 2.5 kW into the batteries.
To replace three days of use: 9 ÷ 2.5 = 3.6 hours of generator time, plus extra for charging losses and the slower final stage of charging. Running the generator every third day for about 4 to 5 hours, rather than every day for 1.5 hours, means fewer cold starts and longer, more efficient runs. Keep the generator in a heated or insulated, ventilated enclosure, and its exhaust well away from air intakes.
Plan maintenance for the light months. Oil changes, filter supplies, spare starter batteries and a second means of charging are worth more in January than extra panels.
Wildfire, flood and isolation
- Wildfire: the boreal forest of the southern NWT has large fires, and whole communities have been evacuated. Clear fuel around cabins, use metal roofs and know your evacuation route, which may be by water or air.
- Flooding: spring breakup on the Mackenzie and Hay rivers brings ice jams and flooding. Keep buildings and fuel above known flood levels.
- Thawing ground: warming permafrost can cause slumps along river banks and lake shores. Set buildings back from banks.
- Isolation: carry a satellite communication device, winter survival gear and spare parts for every critical system, and leave a travel plan with someone before every trip on the land or ice.
Practical system choices
- Heat: oil, propane and wood (south of the tree line) are the main fuels. Store a full winter's fuel, plus a margin, in approved tanks set back from buildings. Propane does not vaporize below about −42 °C (−44 °F), so outdoor propane tanks fail in deep cold.
- Power: solar from March to September, a generator from October to February. Small wind turbines suit exposed Arctic sites but must survive icing and high wind.
- Water and sewage: in communities, trucked water and sewage pump-out with insulated holding tanks are standard. At remote cabins, water is often hauled or cut as lake ice. Keep tanks in heated space.
- Water storage: two people using 40 L (10.6 US gal) each a day with careful habits need 2 × 40 × 14 = 1,120 L for two weeks between hauls. A 1,200 L tank weighs about 1.2 tonnes full and must sit on a floor built for it, inside the heated envelope.
- Fuel storage: use approved, double-walled or diked tanks, set back from buildings and water, on a level, drained base. Spills on frozen ground spread and are hard to clean up.
- Batteries: keep them warm. Many batteries cannot be charged below freezing; check the manufacturer's limits.
Alaska
Northern and western Alaska share this climate and the same permafrost building practices. Land there is held by the federal and state governments and by Alaska Native corporations; confirm ownership and permits before using any land.
Key points
- Design cold is −39 to −45 °C, with 8,400 to 11,900 heating degree-days; fuel supply limits what a remote building can burn.
- Polar night lasts about a month at Inuvik and six weeks at Cambridge Bay. Spring is the best solar season; tilt panels steeply or mount them on walls.
- On permafrost, raise buildings with a ventilated space below, use a thermal break at the piles and keep water away from foundations.
- In the NWT, settlement lands in the Inuvialuit, Gwich'in, Sahtu and Tłı̨chǫ regions are private; public land is managed by the GNWT.
- In Nunavut, Inuit Owned Lands are managed by NTI and the Regional Inuit Associations; projects start with the Nunavut Planning Commission.
- NWT burn permits are required by law; wells must be 30 m from pollution sources and privies 30 m downstream of wells.
This guide is general information. Codes, permits and safety requirements vary by province, state and municipality. Check local rules and use a qualified professional for electrical, gas, chimney and septic work where required.
The Comprehensive Off-Grid Manual
Every off-grid system in one manual, with worked examples, checklists and northern-climate detail.
More guides
Off-Grid Living on the BC Coast and Vancouver Island
Coastal BC design climate, snow and wind loads, winter solar, water and septic rules, owner-builder and dock permits, burning and wildfire for off-grid sites.
Off-Grid Living in Interior BC, the Rockies and Alberta
Interior BC and Alberta design cold, snow loads, frost, winter solar, water, septic, permit and fire rules, wildfire and flood risk, and system choices.
Off-Grid Living on the Prairies
Prairie design cold, snow and wind loads, frost depth, solar by month, Saskatchewan and Manitoba septic and burning rules, dugouts, floods and systems.